User manual ASROCK Z75 PRO3

[. . . ] Z75 Pro3 User Manual Version 1. 0 Published February 2012 Copyright©2012 ASRock INC. All rights reserved. 1 Copyright Notice: No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe. Disclaimer: Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this manual. [. . . ] Please be noted that the password, date, time, user default profile, 1394 GUID and MAC address will be cleared only if the CMOS battery is removed. 31 2. 11 Onboard Headers and Connectors Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard! Serial ATA2 Connectors (SATA2_2: see p. 13, No. 17) SATA2_2 SATA2_3 SATA2_4 SATA2_5 These four Serial ATA2 (SATA2) connectors support SATA data cables for internal storage devices. The current SATA2 interface allows up to 3. 0 Gb/s data transfer rate. These two Serial ATA3 (SATA3) Serial ATA3 Connectors (SATA3_0: see p. 13, No. 16) SATA3_1 SATA3_0 connectors support SATA data cables for internal storage devices. The current SATA3 interface allows up to 6. 0 Gb/s data transfer rate. Serial ATA (SATA) Data Cable (Optional) Either end of the SATA data cable can be connected to the SATA / SATA2 / SATA3 hard disk or the SATA2 / SATA3 connector on this motherboard. Besides four default USB 2. 0 ports on the I/O panel, there are three USB 2. 0 headers on this motherboard. Each USB 2. 0 header can support two USB 2. 0 ports. USB 2. 0 Headers (9-pin USB4_5) (see p. 13, No. 23) 32 (9-pin USB8_9) (see p. 13, No. 24) USB_PWR P-9 P+9 GND DUMMY 1 GND P+8 P-8 USB_PWR USB 3. 0 Header (19-pin USB3_0_1) (see p. 13, No. 9) Vbus IntA_P0_SSRXIntA_P0_SSRX+ GND IntA_P0_SSTXIntA_P0_SSTX+ GND IntA_P0_DIntA_P0_D+ Vbus IntA_P1_SSRXIntA_P1_SSRX+ GND IntA_P1_SSTXIntA_P1_SSTX+ GND IntA_P1_DIntA_P1_D+ DUMMY Besides two default USB 3. 0 ports on the I/O panel, there is one USB 3. 0 header on this motherboard. This USB 3. 0 header can support two USB 3. 0 ports. Infrared Module Header (5-pin IR1) (see p. 13, No. 26) 1 1 IRTX +5VSB DUMMY This header supports an optional wireless transmitting and receiving infrared module. GND IRRX Consumer Infrared Module Header (4-pin CIR1) (see p. 13, No. 25) 1 GND IRTX IRRX ATX+5VSB This header can be used to connect the remote controller receiver. Front Panel Audio Header (9-pin HD_AUDIO1) (see p. 13, No. 30) 1 GND PRESENCE# MIC_RET OUT_RET This is an interface for front panel audio cable that allows convenient connection and control of audio devices. OUT2_L J_SENSE OUT2_R MIC2_R MIC2_L 1. High Definition Audio supports Jack Sensing, but the panel wire on the chassis must support HDA to function correctly. Please follow the instruction in our manual and chassis manual to install your system. If you use AC’97 audio panel, please install it to the front panel audio header as below: A. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L. MIC_RET and OUT_RET are for HD audio panel only. [. . . ] Then choose the directory (xx\AMD64\) you have copied in the first step. 67 E. Please keep the USB flash disk installed until the system's first reboot. Continue to install OS by following the Windows® instructions. Follow Windows® Installation Guide to install OS. [. . . ]