User manual ASUS 27T1EH

[. . . ] Specifications and information contained in this manual ae furnished for informational use only, and are subject to change at any time without notice, and should not be construed as a commitment by ASUS. ASUS assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual, including the products and software described in it. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. ii Contents Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Set to [Enhanced] to support two SATA 6. 0 Gb/s and two SATA 3. 0 Gb/s devices. Set to [Compatible] when using Windows 98/NT/2000/MS-DOS. Up to four SATA devices are supported under these operating systems. Configuration options: [Disabled] [Enhanced] [Compatible] Serial-ATA Controller 1 [Enhanced] This item appears only when you set the SATA Mode item to [IDE Mode]. Set to [Enhanced] to support two SATA 3. 0 Gb/s devices. Configuration options: [Disabled] [Enhanced] 5-22 Chapter 5: BIOS setup S. M. A. R. T. (Self-Monitoring, Analysis and Reporting Technology) is a monitor system. When read/write of your hard disk errors occur, this feature allows the hard disk to report warning messages during the POST. Configuration options: [Enabled] [Disabled] 5. 4. 5 PCHSCUSASConfiguration The PCH SCU SAS configuration items appears only when you installed the ASRK Module (optional) on the motherboard. 5. 4. 6 PCI Subsystem Settings Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc. Advanced V 2. 05. 00 [EFI Compatible ROM] In case of multiple Option ROMs (Legacy and EFI Compatible), specifies what PCI option ROM to lanuch. PCI Bus Driver Version PCI Option ROM Handling PCI ROM Priority PCI 64bit Resources Handling Above 4G Decoding [Disabled] PCI Common Setting PCI Latency Timer [32 PCI Bus Clocks] VGA Palette Snoop [Disabled] PERR# Generation [Disabled] SERR# Generation [Disabled] PCI Express Settings PCI Express Gen2 Settings PCIE Slot Option Rom Configuration : Select Screen : Select Item Enter: Select Item +/-: Change Opt. F1: General Help F2: Previous Values F5: Optimized Defaults F10: Save & Exit ESC: Exit Version 2. 14. 1219. Copyright (C) 2011 American Megatrends, Inc. Completion Timeout [Default] In device Functions that support Completion Timeout programmability, allows system software to modify the Completion Timout value. If `Shorter' is selected, software will use shorter timeout ranges supported by hardware. If `Longer' is selected, software will use. Configuration options: [Default] [Shorter] [Longer] [Disabled] ARI Forwarding [Disabled] If supported by hardware and set to `Enabled', the Downstream Port disables its traditional Device Number field being 0 enforcement when turning a Type 1 Configuration Request into a Type 0 Configuration Request, permitting access to Extended Functions in ab ART Device immediately below the port. Configuration options: [Disabled] [Enabled] Atomic0pRequesterEnable[Disabled] If supported by hardware and set to `Enabled', this function initistes Atomc0p Requests only if Bus Master Enable bit is in the Command Register set. Configuration options: [Disabled] [Enabled] Atomic0p Egress Blocking [Disabled] If supported by hardware and set to `Enabled', outbound Atomic0p Requests via Egress Ports will be blocked. Configuration options: [Disabled] [Enabled] ID0RequestEnable[Disabled] If supported by hardware and set to `Enabled', this permits setting the number of ID-Based Ordering (ID0) bit (Attribute [2]) requests to be initiated. Configuration options: [Disabled] [Enabled] 5-26 Chapter 5: BIOS setup ID0 Completion Enable [Disabled] If supported by hardware and set to `Enabled', this permits setting the number of ID-Based Ordering (ID0) bit (Attribute [2]) requests to be initiated. Configuration options: [Disabled] [Enabled] LTR Mechanism Enable [Disabled] If supported by hardware and set to `Enabled', this enables the Latency Tolerance Reporting (LTR) Mechanism. Configuration options: [Disabled] [Enabled] End-EndTLPPrefixBlocking[Disabled] If supported by hardware and set to `Enabled', this function will bolck forwarding of TLPs containing End-End TLP Prefixes. Configuration options: [Disabled] [Enabled] PCI Express GEN2 Link Register Target Link Speed [Auto] Configuration options: [Auto] [Force to 2. 5 GT/s] [Force to 5. 0 GT/s] Clock Power Management [Disabled] Configuration options: [Disabled] [Enabled] Compliance SOS [Disabled] Configuration options: [Disabled] [Enabled] Hardware Autonomous Width [Enabled] Configuration options: [Enabled] [Disabled] Hardware Autonomous Speed [Enabled] Configuration options: [Enabled] [Disabled] ASUS 27T1EH 5-27 PCIESlotOptionRomConfiguration Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc. Advanced Legacy 0pROM Support Launch Storage 0pROM PCIE1 PCIE2 PCIE3 PCIE4 PCIE5 Option Option Option Option Option Rom Rom Rom Rom Rom [Enabled] [Enabled] [Enabled] [Enabled] [Enabled] [Enabled] Enables or disables boot option for legacy mass storage device with option ROM. : Select Screen : Select Item Enter: Select Item +/-: Change Opt. [. . . ] The support DVD automatically displays the Drivers menu if Autorun is enabled in your computer. If Autorun is NOT enabled in your computer, browse the contents of the support DVD to locate the file ASSETUP. EXE from the BIN folder. Double-click the ASSETUP. EXE to run the support DVD. 3. Click the ASPEED AST2300 Display Driver to begin installation. 4. When the ASPEED Graphics installation wizard appears, click Next to start the installation. ASUS 27T1EH 7-19 5. Toggle I accept the terms in the license agreement and click Next to continue. 6. Enter the user information and click Next to continue. 7. Select a setup type and click Next to continue. 7-20 Chapter 7: Driver installation 8. Click Install to start driver installation. 9. When the installation completes, click Finish to restart your computer before using the program. ASUS 27T1EH 7-21 7. 5 Intel® C600 Series Chipset SAS RAID (SATA mode) Drivers This section provides the instructions on how to install the Intel® C600 Series Chipset SAS RAID (SATA mode) Drivers on the system. You need to manually install the Intel® C600 Series Chipset SAS RAID (SATA mode) Drivers on a Windows operating system. Restart the computer, and then log on with Administrator privileges. [. . . ]