User manual ASUS AP120-E1

[. . . ] AP120-E1 P4 Pedestal Server/Workstation 800MHz Front Side Bus User Guide E1502 First Edition V1 March 2004 Copyright © 2004 ASUSTeK COMPUTER INC. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. ASUS provides this manual "as is" without warranty of any kind, either express or implied, including but not limited to the implied warranties or conditions of merchantability or fitness for a particular purpose. In no event shall ASUS, its directors, officers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of profits, loss of business, loss of use or data, interruption of business and the like), even if ASUS has been advised of the possibility of such damages arising from any defect or error in this manual or product. [. . . ] The lever clicks on the side tab to indicate that it is locked. 2-6 Chapter 2: Hardware setup 6. Install a CPU heatsink and fan following the instructions that came with the heatsink package. ASUS provides an Intel®-certified CPU fan and heatsink assembly as an optional item for your AP120-E1 system. Refer to the "Installation options" chapter for details. 7. Connect the CPU fan cable to the CPU_FAN1 connector on the motherboard. CPU fan connector (CPU_FAN1) Don't forget to connect the CPU fan connector!Hardware monitoring errors may occur if you fail to plug this connector. ASUS AP120-E1 user guide 2-7 2. 5 Installing memory modules The motherboard comes with three (3) Double Data Rate (DDR) Dual Inline Memory Module (DIMM) sockets. These sockets support up to 3GB system memory using 184-pin unbuffered non-ECC PC3200/2700/2100 DDR DIMMs. The following figure shows the location of the DDR DIMM sockets. ® P4P800S-E DIMM2 P4P800S-E 184-Pin DDR DIMM Sockets Obtain DDR DIMMs only from ASUS qualified vendors to ensure system system stability. The DDR400 Qualified Vendors List (QVL) is provided below. Visit http://www. asus. com/products/server/ RAMsupport. htm for the latest QVL. 2. 5. 1 Memory configurations You may install 64MB, 128MB, 256MB, 512MB, and 1GB DDR DIMMs into the DIMM sockets. Table 1: Qualified DDR400 vendors list This table lists the memory modules that have been tested and qualified for use with this motherboard. Size 256MB 256MB 512MB 512MB Vendor Apacer Trancend Infineon Kingston Part Number 77. 10638. 465 V58C2256804SAT75 HYS64D64320GU-5-B KVR333X64C25/512 Chip Brand SAMSUNG Trancend Infineon Kingston DIMM1 DIMM3 104 Pins 80 Pins Chip Number K4H560838D V58C2256804SAT75 HYB25D256800BT-5 D3208DH1T-6 2-8 Chapter 2: Hardware setup 2. 5. 2 DIMM installation Make sure to unplug the power supply before adding or removing DIMMs or other system components. Failure to do so may cause severe damage to both the motherboard and the components. Follow these steps to install a DIMM. Unlock a DIMM socket by pressing the retaining clips outward. Align a DIMM on the socket such that the notch on the DIMM matches the break on the socket. A DDR DIMM is keyed with a notch so that it fits in only one direction. DO NOT force a DIMM into a socket to avoid damaging the DIMM. Unlocked retaining clip DDR DIMM notch 3. Firmly insert the DIMM into the socket until the retaining clips snap back in place and the DIMM is properly seated. Locked retaining clip 2. 5. 3 Removing a DIMM Follow these steps to remove a DIMM. Simultaneously press the retaining clips outward to unlock the DIMM. Support the DIMM lightly with your fingers when pressing the retaining clips. The DIMM might get damaged when it flips out with extra force. 2. ASUS AP120-E1 user guide 2-9 2. 6 Installing a hard disk drive The server/workstation system supports one IDE/Serial ATA hard disk drive through a detachable hard disk drive cage. You may purchase a second hard disk drive cage to install an additional HDD. Refer to the next chapter for details. Hard disk drive cage Configure your hard disk drive as Master/Slave device before installing it to the chassis. Refer to the HDD documentation on how to set the drive as a Master/Slave device. 2. 6. 1 Qualified hard disk drives The table below lists the hard disk drives tested and qualified for use with this server/workstation. Table 2: Qualified hard disk drive vendors list Vender Seagate Seagate IBM/Hitachi Maxtor IBM/Hitachi Maxtor Seagate IBM/Hitachi Seagate Seagate Seagate Maxtor Maxtor Model ST380021A ST3120023A Deskstart IC35L090AVV207 MAXTOR/6Y80L0 Deskstart IC35L120AVV207 MAXTOR/6Y160L0 ST3160023A Deskstart IC35L180AVV207 ST380013AS ST3120026AS ST3160023AS 6Y080M0 6Y120M0 Interface IDE IDE IDE IDE IDE IDE IDE IDE SATA SATA SATA SATA SATA Speed 7200rpm 7200rpm 7200rpm 7200rpm 7200rpm 7200rpm 7200rpm 7200rpm 7200rpm 7200rpm 7200rpm 7200rpm 7200rpm Capacity 80GB 120GB 80GB 80GB 120GB 160GB 160GB 180GB 80GB 120GB 160GB 80GB 120GB 2-10 Chapter 2: Hardware setup 2. 6. 2 Hard disk drive installation The detachable hard disk drive cage can accommodate one IDE or Serial ATA hard disk drive. To install an IDE hard disk drive: Configure your hard disk drive as Master/Slave device before installing it to the drive cage. Refer to the HDD documentation on how to set the drive as a Master/Slave device. 1 2 Screw holes 1. Press the HDD cage lock while pulling the cage out from the chassis. [. . . ] Press the locking lever, then insert the hooks to the chassis holes. 3 2 4. Secure the expansion card holder with one screw. 4 3-8 Chapter 3: Optional components To hold long expansion cards: 1. Place the card holder at level with the expansion card. The smaller card holder is for long AGP cards while the other card holders are for long PCI cards. 2 2. Loosen the screw(s) to adjust the card holder forward or sideward until its groove fits the edge of the expansion card. 3. [. . . ]