User manual ASUS AP130-D

[. . . ] ® AP130-D Pentium 4 Pedestal Server ® User's Manual Disclaimer/Copyrights No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. ASUS PROVIDES THIS MANUAL "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. [. . . ] Use the power cable with a properly grounded electrical outlet to avoid electrical shock. Operation Safety IMPORTANT · · · Any mechanical operation on this server must be conducted by certified or experienced engineers. Before operating the server, carefully read all the manuals included with the server package. Before using the server, make sure all cables are correctly connected and the power cables are not damaged. If any damage is detected, contact your dealer as soon as possible. To avoid short circuits, keep paper clips, screws, and staples away from connectors, slots, sockets and circuitry. Avoid dust, humidity, and temperature extremes. Place the server on a stable surface. · · 7 8 Introduction "About This Manual" introduces the contents of this document. This part includes the target audience, chapter description, and conventions used. It also lists other sources of information that are not contained in this manual. ASUS AP130-D Pedestal Server About This Manual 9 Audience This manual is intended for system integrators, and experienced users with at least basic knowledge of configuring an entry-level server. Contents This manual contains the following parts: 1. Introduction: About This Manual This part introduces the contents of this document. It includes the target audience, chapter description, and conventions used. It also lists other sources of information that are not contained in this manual. Chapter 1: System Overview This chapter describes the general features of the AP130-D server. It includes sections on front panel and rear panel specifications. Chapter 2: Hardware Setup This chapter lists the hardware setup procedures that you have to perform when installing system components. Chapter 3: Powering Up This chapter tells how to get started with the AP130-D server after you have installed the basic components. It includes sections on front panel, rear panel, and internal features of the server. 1. 1 System Features The ASUS AP130-D is a stylish barebone server featuring the ASUS P4B266-M motherboard. The server supports the Intel® Pentium® 4 478/ Northwood processor, and includes the latest I/O, audio, and video technologies through the chipsets embedded on the motherboard. Following are highlights of the server's many features. · · · Processor: Support for Intel Pentium 4 processor with 512KB L2 cache and speeds of up to over 2GHz Memory: Two DIMM sockets support up to 2GB of system memory using unbuffered ECC or non-ECC PC2100/PC1600 DDR DIMMs System Chipset: Intel 845D (Brookdale) chipset composed of Intel Memory Controller Hub (MCH). The MCH along with the south bridge Intel I/O Controller Hub 2 (ICH2) are interconnected through the Intel proprietary Hub interface. The MCH provides the processor interface, system memory interface, AGP interface, and Hub Interface. [. . . ] Connect a power cord to the power connector on the rear panel. Plug the power cord to a grounded wall socket. Power Connector Voltage Selector Power On Turn on the server by pressing the power switch on the front panel. Power Switch Check Power Status After turning on the power, the power LED lights up. If it doesn't, check the power connection. Power LED 32 Chapter 3: Powering Up Appendix A This appendix gives information on the 200W switching power supply that comes with the AP130-D server. ASUS AP130-D Pedestal Server Power Supply 33 A. 1 General Description The server comes with a 200W ATX power supply with universal AC input that includes PFC and ATX-compliant output cables and connectors. The power supply has an internal cooling fan. [. . . ]