User manual ASUS AP1700-S5 AP1700-S5 ENGLISH VERSION MANUAL PDF FILE

[. . . ] ® AP1700 Intel® Xeon Tower/5U Rackmount Server with 533MHz FSB support User's Manual Disclaimer/Copyrights No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. ASUS PROVIDES THIS MANUAL "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. [. . . ] This mark indicates the processor Pin 1 that should match a specific corner of the CPU socket. Incorrect installation of the CPU into the socket may bend the pins and severely damage the CPU!The motherboard supports either one or two CPUs. If you are installing only one CPU, you MUST install it in CPU socket 1. Otherwise, the red motherboard LED will light up as warning. Use Prestonia CPUs with the same FSB speed and specifications when installing on both CPU sockets. CPU Socket 1 (outer socket) CPU Socket 2 (inner socket) User's Manual 2-5 2. 3. 2 Installing the CPU If you are installing only one CPU, install in CPU socket 1. Follow these steps to install a CPU. Locate the 604-pin ZIF sockets on the motherboard. Unlock the socket by pressing the lever sideways, then lift it up to at least 115° angle. Make sure that the socket lever is lifted up to at least 115° angle, otherwise the CPU does not fit in completely. 2. Position the CPU above the socket as shown. Carefully insert the CPU into the socket until it fits in place. Marked Corner The CPU fits only in one correct orientation. DO NOT force the CPU into the socket to prevent bending the pins and damaging the CPU! 4. When the CPU is in place, press it firmly on the socket while you push down the socket lever to secure the CPU. The lever clicks on the side tab to indicate that it is locked. 2-6 ASUS AP1700 2. 3. 3 Installing the CPU heatsink with fan assembly The Intel® XeonTM processors require especially designed heatsink and fan assembly to ensure optimum thermal condition and performance. Make sure that the heatsink with fan assembly is properly installed on the motherboard. A tilted or improperly installed heatsink with fan assembly can cause damage to motherboard CPU socket and/or CPU. Follow these steps to install the CPU heatsink and fan. Place the heatsink and fan assembly on top of the installed CPU, making sure that it fits in the screw holes of the heatsink bracket found at the bottom of the CPU socket. (The heatsink bracket comes factory installed with the motherboard. ) 2. Make sure all screws fit properly in place. Take caution in tightening screws. Do not over-tighten screws, doing so may damage the motherboard! 4 User's Manual TIP: Follow the sequence shown: half-tighten the screw on one corner of the heatsink and fan, then the next screw on the other corner and so on, making a cross pattern. Repeat until all four screws are tightened properly. 2 3 1 2-7 3. When the heatsink and fan assembly is in place, connect the fan cable to the fan connector on the motherboard labeled CPUFAN1. The fan cable plug is slotted so it fits only in one orientation. If it doesn't fit completely, try reversing it. 4. [. . . ] To remove the power supply case, follow these steps: 1. Remove the two (2) top chassis cover screws to release chassis top panel cover. 2. Remove all power cable connections from SCSI backplane, motherboard, floppy and CD-ROM. Remove the six (6) chassis bar screws and release chassis bar. 4. [. . . ]