User manual ASUS AW171

[. . . ] SK8N User Guide Motherboard E1379 Checklist Revised Edition V2 November 2003 Copyright © 2003 ASUSTeK COMPUTER INC. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. ASUS PROVIDES THIS MANUAL "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. [. . . ] At the DOS prompt, type the command line: afudos /o<filename> where "filename" can be any user provided filename of not more than eight (8) alpha-numeric characters for the main filename and three (3) alpha-numeric characters for the extension name. Press the Enter key. The BIOS information on the screen is for reference only. What you see on your screen may not be exactly the same as shown. Main filename Extension name A:\>afudos /oMYBIOS03. rom AMI Firmware Update Utility - Version 1. 10 Copyright (C) 2002 American Megatrends, Inc. 0x0008CC00 (9%) ASUS SK8N motherboard 4-3 2. The utility will copy the current system BIOS by default to the floppy disk. Make sure that the floppy disk is not write-protected and have enough space (at least 600KB) to store the file. A:\>afudos /oMYBIOS03. rom AMI Firmware Update Utility - Version 1. 10 Copyright (C) 2002 American Megatrends, Inc. done A:\> When the BIOS copy process is complete, the utility returns to the DOS prompt. 4. 1. 4 Using ASUS EZ Flash to update the BIOS The ASUS EZ Flash feature allows you to easily update the BIOS without having to go through the long process of booting from a diskette and using a DOS-based utility. The EZ Flash is built-in the BIOS firmware so it is accessible by simply pressing <Alt+F2> during the Power-On Self Tests (POST). To update the BIOS using ASUS EZ Flash: 1. Visit the ASUS website (www. asus. com) to download the latest BIOS file for your motherboard and rename the downloaded file as SK8N. ROM. To launch EZ Flash, press <Alt+F2> during POST to display the following. User recovery requested. Checking for floppy. . . · · If there is no floppy disk found in the drive, the error message "Floppy not found!" appears. If the correct BIOS file is not found in the floppy disk, the error message "SK8N. ROM not found!" is displayed. Make sure to rename the downloaded BIOS file as "SK8N. ROM". 4-4 Chapter 4: BIOS Setup 4. Insert the floppy disk that contains the BIOS file. If all the necessary files are found in the floppy disk, EZ Flash performs the BIOS update process and automatically reboots the system when done. DO NOT shutdown or reset the system while updating the BIOS!Doing so may cause system boot failure! User recovery requested. Rebooting. 4. 1. 5 Recovering the BIOS with CrashFree BIOS 2 The CrashFree BIOS 2 auto recovery tool allows you to restore BIOS from the motherboard support CD, or from a floppy disk that contains the BIOS file, in case the current BIOS on the motherboard fails or gets corrupted. 1. Prepare the support CD that came with the motherboard or a floppy disk that contains the motherboard BIOS before proceeding with the BIOS update process. If you have saved a copy of the original motherboard BIOS to a bootable floppy disk, you may also use this disk to restore the BIOS. See section "4. 1. 1 Creating a bootable floppy disk. " To recover the BIOS from a floppy disk: 1. When a corrupted BIOS is detected, the following screen message appears. Bad BIOS checksum. Checking for floppy. . . ASUS SK8N motherboard 4-5 3. [. . . ] On boot-up, an error message notifies of a system failure. Press <Ctrl+F> to enter the FastBuildTMMain Menu. Select 3 for View Array to verify the ID of the defunct hard disk. Power off the system and replace the hard disk with an identical model. [. . . ]