User manual ASUS E1932 PUNDIT-PE2

[. . . ] Pundit Barebone System Model PE2 E1932 First edition V1 February 2005 Copyright © 2005 ASUSTeK COMPUTER INC. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. ASUS PROVIDES THIS MANUAL "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. [. . . ] Check the box before the M i c 2 S e l e c t option to enable the front panel microphone port. Click C l o s e e. 3. The rear panel Mic port (pink) is automatically disabled when you enable the front panel Mic port. Only one Mic port works at a time. 3-8 Chapter 3: Getting started Chapter 4 ASUS Pundit-PE2 Motherboard info This chapter gives information about the motherboard that comes with the system. This chapter includes the motherboard layout, jumper settings, and connector locations. 4. 1 Motherboard overview 27. 2cm (10. 7in) Motherboard layout DDR DIMM2 (64/72-bit, 184-pin module) DDR DIMM1 (64/72-bit, 184-pin module) USB34 FONT MIC FONT LOUT CD AUX IE1394_1 Socket 478 AD1980 ADAPTER SiS 651 Host Memory Controller PWRSW AUD_CON IE1394_2 VIA VT6307 BUZZER RTL 8201BL CLRTC CHA_FAN CPU_FAN CR2032 3V Lithium Cell CMOS Power SiS 962LUA Super I/O LAN_USB78 PRI_IDE 4 Mb ISA PCI1 PS/2 T:Mouse B:Keyboard IDEPWR SBPWRLED 4-2 Chapter 4: Motherboard info LED_CON 26. 9cm (10. 6in) 4. 2 Jumper Clear RTC RAM (CLRTC) This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in CMOS, which include system setup information such as system passwords. Turn OFF the computer and unplug the power cord. Move the jumper cap from pins 1-2 (default) to pins 2-3. Keep the cap on pins 2-3 for about 5~10 seconds, then move the cap back to pins 1-2. Plug the power cord and turn ON the computer. Hold down the <Del> key during the boot process and enter BIOS setup to re-enter data. Except when clearing the RTC RAM, never remove the cap on CLRTC jumper default position. Removing the cap will cause system boot failure! 4. 6. CLRTC 12 Normal (Default) 23 Clear CMOS Clear RTC RAM ASUS Pundit-PE2 4-3 4. 3 4. 3. 1 4. 3. 2 1. Connectors Rear panel connectors Internal connectors Refer to section "1. 3 Rear panel" for a description of the rear panel I/O ports. Primary IDE connector (40-1 pin PRI_IDE) This connector is for an Ultra DMA 100/66 signal cable. The Ultra DMA 100/66 signal cable has three connectors: a blue connector for the primary IDE connector on the motherboard, a black connector for an Ultra DMA 100/66 IDE slave device (optical drive/hard disk drive), and a gray connector for an Ultra DMA 100/66 IDE master device (hard disk drive). If you install two hard disk drives, you must configure the second drive as a slave device by setting its jumper accordingly. Refer to the hard disk documentation for the jumper settings. · Pin 20 on the IDE connector is removed to match the covered hole on the Ultra DMA cable connector. This prevents incorrect insertion when you connect the IDE cable. Use the 80-conductor IDE cable for Ultra DMA 100/66 IDE devices. · PRI_IDE PIN 1 NOTE: Orient the red markings (usually zigzag) on the IDE ribbon cable to PIN 1. IDE connector 4-4 Chapter 4: Motherboard info 2. CPU and Chassis Fan connectors (3-pin CPU_FAN, CHA_FAN) The fan connectors support cooling fans of 350 mA~740 mA (8. 88 W max. ) or a total of 1 A~2. 22 A (26. 64 W max. ) at +12V. Connect the fan cables to the fan connectors on the motherboard, making sure that the black wire of each cable matches the ground pin of the connector. Do not forget to connect the fan cables to the fan connectors. Insufficient air flow inside the system may damage the motherboard components. Do not place jumper caps on the fan connectors! CHA_FAN CPU_FAN Rotation +12V GND Rotation +12V GND Fan connectors 3. Internal audio connectors (4-pin CD1, AUX1) These connectors allow you to receive stereo audio input from audio sources such as an optical drive, TV tuner, or MPEG card. Right Audio Channel Ground Ground Left Audio Channel CD (Black) AUX (White) Internal audio connectors Enable the CD-IN function in the audio utility when using these connectors. ASUS Pundit-PE2 4-5 4. IDE power connector (4-pin IDEPWR) The IDE power connector is for the IDE power cable. This connector supplies power to the hard disk drive and the slim optical drive. IDEPWR IDE power connector 5. Power switch connector (2-pin PWRSW) This connects to the the system power switch button on the system front panel. PWRSW Power switch connector 4-6 +5V GND GND +12V Chapter 4: Motherboard info 6. Rear panel audio connectors (10-1 pin AUD_CON) This connector is for the ASUS proprietary rear panel audio board that supports the rear panel audio I/O ports. +5V VREFOUT GND SURR_L SURR_R 1 AUD_CON LINE_IN_RT LINE_IN_LT LOUT_R LOUT_L Rear panel audio connector 7. Front panel LED connector (6-pin LED_CON) The connector is for the power and HDD activity LED in the system front panel. LED_CON HDD LED Power LED Front panel LED connector 1 ASUS Pundit-PE2 4-7 4-8 Chapter 4: Motherboard info Chapter 5 This chapter tells how to change system settings through the BIOS Setup menus and describes the BIOS parameters. ASUS Pundit-PE2 BIOS setup 5. 1 Managing and updating your BIOS The following utilities allow you to manage and update the motherboard Basic Input/Output System (BIOS) setup. [. . . ] Configuration options: [USB ZIP/Flash] [USB FDD] [LS120] [ZIP] [ATAPI MO] [Disabled] Use the front panel USB ports if you will boot the system using a USB FDD or USB ZIP device. IDE Hard Drive Allows you to select the IDE hard disk drive to use in the boot sequence. Pressing [Enter] will show the product ID of the connected IDE hard disk drive. ATAPI CD-ROM Allows you to select the ATAPI CD-ROM drive to use in the boot sequence. Pressing [Enter] will show the product ID of the connected ATAPI CD-ROM drives. 5-26 Chapter 5: BIOS setup Other Boot Device Select [INT18 Device (Network)] Configuration options: [Disabled] [INT18 Device (Network)] Plug & Play O/S [No] Allows you to use a Plug-and-Play (PnP) operating system to configure the PCI bus slots instead of using the BIOS. When [Yes] is selected, interrupts may be reassigned by the OS. [. . . ]