User manual ASUS ESC4000/FDR G2

[. . . ] No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. ASUS provides this manual "as is" without warranty of any kind, either express or implied, including but not limited to the implied warranties or conditions of merchantability or fitness for a particular purpose. In no event shall ASUS, its directors, officers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of profits, loss of business, loss of use or data, interruption of business and the like), even if ASUS has been advised of the possibility of such damages arising from any defect or error in this manual or product. Specifications and information contained in this manual ae furnished for informational use only, and are subject to change at any time without notice, and should not be construed as a commitment by ASUS. [. . . ] Configuration options: [Disabled] [Enabled] The following item appears only when you set Runtime Error Logging Support to [Enabled]. 5 Server Mgmt menu The Server Mgmt menu displays the server mgmt status, and allows you to change the settings. The Server Mgmt menu appears only when you install ASMB card on the motherboard. Xx [Disabled] [10 minutes] [Reset] Wait for BMC response for specified timeout In PILOTII, BMC starts at the same time when BIOS starts during AC power ON. It takes arround 30 seconds to initialize Host to BMC interfaces. Main BMC Firmware: O/S Watchdog Timer O/S Wtd Timer Timeout O/S Wtd Timer Policy System Event Log BMC network configuration O/S Watchdog Timer [Disabled] If enabled, starts a BIOS timer which can only be shut off by Intel Management Software after the OS loads. Helps determine that the OS sucessfully loaded or follows the O/S Boot Watchdog TImer Policy. Configuration options: [Enabled] [Disabled] O/S Wtd Timer Timeout [10 minutes] Allows to configure the length of the O/S Boot Watchdog Timer. not available if O/S Boot Watchdog Timer is disabvled. Configuration options: [5 minutes] [10 minutes] [15 minutes] [20 minutes] O/S Wtd Timer Policy [Reset] Allows to configure how the system should respond if the OS Boot Watchdog Timer expires. Server Mgmt Change this to enable or disable all features of system Event Logging during boot. Enabling/Disabling Options SEL Components Erasing Settings Erase SEL When SEL is Full Custom EFI Logging Options Note: All values changed here do not take effect until computer is restarted. SEL Components [Disabled] Allows you to enable or disable all features of system Event Logging during boot. The following items appears only when you set SEL Components to [Enabled]. All values changed here do not take effect until computer is restarted. Erase SEL [No] Allows to choose options for erasing SEL. Configuration options: [No] [Yes, On next reset] [Yes, On every reset] When SEL is Full [Do Nothing] Allows to choose options for reactions to a full SEL. Unspecified option will not modify any BMC network parameters during BIOS phase BMC network configuration DM_KAN1 DM_LAN1 IP Address in BMC: DM_LAN1 Subnet Mask in BMC: DM_LAN1 Gateway Address in BMC : DM_LAN1 MAC Address in BMC: DM_LAN1 Address Source in BMC: Configuration Address source Lan1 Lan1 Lan1 Lan1 Lan1 Lan1 IP Address in BMC: Subnet Mask in BMC: Gateway Address in BMC: MAC Address in BMC: Address Source in BMC: 192. Unspecified option will not modify any BMC network parameters during BIOS phase. Configuration options: [Previous State] [Static Mode] [DHCP Mode] The following items appears only when you set ConfigurationAddresssource to [Static Mode]. The Event Logs allows you to change or view the event log settings. Enabling/Disabling Options Smbios Event Log Erasing Settings Erase Event Log When Log is Full Change this to enable or disable all features of Smbios Event Logging during boot. [. . . ] You can also find this information on the inside front cover of this user guide. 7-32 Chapter 7: Driver installation 7. 9 Mellanox ConnectX-3 Infiniband driver installation (ESC4000/FDR G2 only) This section provides instructions on how to install the Mellanox driver. 1 Windows operating system You need to manuall install the Mellanox driver on a Windows® operating system. [. . . ]