User manual ASUS M2N-XE

[. . . ] IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. ii Contents Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The plugs from the power supply are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit. · We recommend that you use an ATX 12 V Specification 2. 0-compliant power supply unit (PSU) with a minimum of 300 W power rating. This PSU type has 24-pin and 4-pin power plugs. If you intend to use a PSU with 20-pin and 4-pin power plugs, make sure that the 20-pin power plug can provide at least 15 A on +12 V and that the PSU has a minimum power rating of 300 W. The system may become unstable or may not boot up if the power is inadequate. Do not forget to connect the 4-pin ATX +12 V power plug; otherwise, the system will not boot up. We recommend that you use a PSU with higher power output when configuring a system with more power-consuming devices. The system may become unstable or may not boot up if the power is inadequate. You must install a PSU with a higher power rating if you intend to install additional devices. · · · · EATXPWR M2N-XE ® M2N-XE ATX power connectors +3 Volts -12 Volts Ground PSON# Ground Ground ATX12V Ground GND GND -5 Volts +12V DC +12V DC +5 Volts +5 Volts +5 Volts Ground +3 Volts +3 Volts Ground +5 Volts Ground +5 Volts Ground Power OK +5V Standby +12 Volts +12 Volts +3 Volts ASUS M2N-XE 1-29 1 4 . System panel connector (20-1 pin PANEL) This connector supports several chassis-mounted functions. PLED M2N-XE SPEAKER +5V Ground Ground Speaker PLED+ PANEL IDE_LED+ IDE_LED® PLED- IDE_LED RESET PWRSW M2N-XE System panel connector * Requires an ATX power supply. The sytem panel connector is color-coded for easy connection. Refer to the connector description below for details. · · · · System power LED (Green 3-pin PLED) This 3-pin connector is for the system power LED. Insert the Windows® 2000 CD to the optical drive. Click S t a r t then select R u n t, n. 2-2 Chapter 2: BIOS setup d. From the Open field, type D:\bootdisk\makeboot a: assuming that D: is your optical drive. Press <Enter>, then follow screen instructions to continue. Copy the original or the latest motherboard BIOS file to the bootable floppy disk. 2. 1. 2 ASUS EZ Flash utility The ASUS EZ Flash feature allows you to update the BIOS without having to go through the long process of booting from a floppy disk and using a DOS-based utility. The EZ Flash utility is built-in the BIOS chip so it is accessible by pressing <Alt> + <F2> during the Power-On Self Tests (POST). Visit the ASUS website (www. asus. com) to download the latest BIOS file for the motherboard and rename the same to A 8 N V M C S M . Save the BIOS file to a floppy disk, then restart the system. Press <Alt> + <F2> during POST to display the following. EZFlash starting BIOS update Checking for floppy. . . 4. Insert the floppy disk that contains the BIOS file to the floppy disk drive. When the correct BIOS file is found, EZ Flash performs the BIOS update process and automatically reboots the system when done. EZFlash starting BIOS update Checking for floppy. . . Start erasing. . . . . . . | Start programming. . . | Flashed successfully. [. . . ] F10 key can be used for this operation. Exit Options Exit & Save Changes Exit & Discard Changes Discard Changes Load Setup Defaults Select Screen Select Item Enter Go to Sub Screen Tab Select Field F1 General Help F10 Save and Exit ESC Exit v02. 58 (C)Copyright 1985-2004, American Megatrends, Inc. Pressing <Esc> does not immediately exit this menu. Select one of the options from this menu or <F10> from the legend bar to exit. 2-36 Chapter 2: BIOS setup Exit & Save Changes Once you are finished making your selections, choose this option from the Exit menu to ensure the values you selected are saved to the CMOS RAM. An onboard backup battery sustains the CMOS RAM so it stays on even when the PC is turned off. When you select this option, a confirmation window appears. [. . . ]