User manual ASUS M5A97

[. . . ] It can be switched between AGP 2X(3. 3V) or 4X(1. 5V) mode by adjusting the jumper. The factory default for this card is 2X(3. 3V). The GA-8S648(-L) (or any AGP 4X only) motherboards might not function properly, if you install this card without switching the jumper to 4X(1. 5) mode in it. Example 2: Some ATi Rage 128 Pro graphics cards made by "Power Color", the graphics card manufacturer & some SiS 305 cards, their golden finger is compatible with 2X(3. 3V)/4X(1. 5V) mode AGP slot, but they support 2X(3. 3V) only. [. . . ] Disable this function. CMidi Port Address 8300 8330 8Disabled Set Midi Port Address to 300. Set Midi Port Address to 330. (Default Value) Disable this function. CMidi Port IRQ 85 810 Set Midi Port IRQ to 5. (Default Value) GA-8648(-L) Motherboard - 40 - English Power Management Setup CMOS Setup Utility -Copy right (C) 1984-2003 Aw ard Softw are Pow er Management Setup ACPI Suspend Ty pe Soft-Off by PWR_BTTN Sy stem After AC Back IRQ [3-7, 9-15], NMI ModemRingOn PME Ev ent Wake Up Pow er On by Key board Pow er On by Mouse Resume by Alarm x Month Alarm x Day (of Month) x Time (hh:mm:ss) Pow er LED in S1 state higf: Mov e [S1(POS)] [Off] [Off] [Enabled] [Enabled] [Enabled] [Disabled] [Disabled] [Disabled] NA 0 000 [Blinking] Enter:Select +/-/PU/PD:Value F10:Sav e ESC:Ex it F1:General Help [S3] Set suspend ty pe to Suspend to RAM under ACPI OS Item Help Menu Lev el u [S1] Set suspend ty pe to Pow er On Suspend under ACPI OS F5:Prev ious Values F6:Fail-Safe Defaults F7:Optimized Defaults Figure 5: Pow er Management Setup C ACPI Suspend Type 8S1(POS) 8S3(STR) Set ACPI suspend ty pe to S1. (Default Value) Set ACPI suspend ty pe to S3. C Soft-off by PWR_BTTN 8Off The user press the pow er button once, he can turn off the sy stem. (Default Value) 8Suspend The user press the pow er button once, then he can enter suspend mode. C System after AC Back 8LastState When AC-pow er back to the sy stem, the sy stem w ill return to the Last state before AC-pow er off. 8Off When AC-pow er back to the sy stem, the sy stem w ill be in "Off" state. (Default Value) 8On When AC-pow er back to the sy stem, the sy stem w ill be in "On" state. - 41 BIOS Setup English C IRQ [3-7, 9-15], NMI 8Disabled 8Enabled Disable this function. (Default v alue) C ModemRingOn 8Disabled 8Enabled Disable Modem Ring on function. (Default Value) C PME Event Wake Up 8Disabled 8Enabled Disable this function. (Default Value) C Power On by Keyboard 8Passw ord Input passw ord (from 1 to 8 characters) and press Enter to set the Key board Pow er On Passw ord. (Default v alue) Enable this function. C CPU Clock (MHz) 8100~355 Select CPU Clock to 100MHz~355MHz. Incorrect using it may cause y our sy stem broken. For pow er End-User use only ! GA-8648(-L) Motherboard - 46 - C DRAM Clock (MHz) 8Please set DRAM Clock according to y our requirement. If y ou use DDR266 DRAM module, please set "DRAM Clock(MHz)" to Auto or 266. If y ou use DDR333 DRAM module, please set "DRAM Clock(MHz)" to Auto or 333. Incorrect using it may cause y our sy stem broken. For pow er End-User use only ! English C AGP/PCI Clock Control 8AUTO 8Manual Set AGP/PCI Clock Control to AUTO. (Default v alue) Set AGP/PCI Clock Control to Manual. C AGP Clock (MHz) 8Please set AGP Clock according to y our requirement. Incorrect using it may cause y our sy stem broken. For pow er End-User use only ! C PCI Clock (MHz) 8Please set PCI Clock according to y our requirement. Incorrect using it may cause y our sy stem broken. [. . . ] Question 13:How to set in the BIOS to bootup from the IDE/ SCSI/ RAID card ?Answer:Please set in the BIOS as follow: 1. Advanced BIOS features-->(SATA)/RAID/SCSI boot order: "SCSI" 2. Advanced BIOS features--> First boot device: "SCSI" Then it depends on the mode(RAID or ATA) that you need to set in RAID/ SCSI BIOS. English GA-8S648(-L) Motherboard - 78 - Troubleshooting If you encounter any trouble during boot up, please follow the troubleshooting procedures . START English Turn off the power and unplug the AC power cable, then remove all of the add-on cards and cables from motherboard. Please make sure motherboard & chassis are not short ? Yes Please isolate the short pin. No Failure has been excluded. Please make sure all jumper settings (such as CPU system bus speed, frequency ratio, voltage and etc. ) are set properly. No Make sure the jumper setting are correct. Yes Failure has been excluded. [. . . ]