User manual ASUS MAXIMUS VI IMPACT C2

[. . . ] IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe. [. . . ] Configuration options: [Auto] [0. 6000] -[2. 2000] ICC Ringback Canceller [Auto] ICC Ringback Canceller can be used to control the noise level at the Integrated Clock Controller. [Enable] to allow better High DMI Frequency O. C. [Disable] to allow better Low DMI Frequency O. C. Clock Crossing VBoot [Auto] The instantaneous voltage value when the rising edge of BCLK DN is equal to the falling edge of the BCLK DP. Configuration options: [Auto] [0. 1000] - [1. 9000] Clock Crossing Reset Voltage [Auto] The instantaneous voltage value when the rising edge of BCLK DN is equal to the falling edge of the BCLK DP. Configuration options: [Auto] [0. 1000] - [1. 9000] Clock Crossing Voltage [Auto] The instantaneous voltage value when the rising edge of BCLK DN is equal to the falling edge of the BCLK DP. Configuration options: [Auto] [0. 1000] - [1. 9000] BCLK Amplitude [Auto] Allows you to adjust the magnitude of the BCLK. Configuration options: [Auto] [+5] - [-5] Tweakers’ Paradise Chapter 3 3-20 Chapter 3: BIOS setup DMI Gen 2 [Auto] Allows you to enable or disable DMI Gen 2. Configuration options: [Auto] [Enabled] [Disabled] DMI De-emphasis Control [-6 dB] SATA Drive Strength [Auto] PCIE Tuning Configure De-emphasis control on DMI. Configuration options: [-6 dB] [-3. 5 db] SATA Drive Strength. Configuration options: [Auto] [+10] - [-10] Internal Graphics [Auto] CPU Power Management Keep IGD enabled based on setup options. It finds the balance between optimal regulating while staying below the current threshold. Configuration options: [Auto] [100%] [87. 5%] [75. 0%] [62. 5%] [50. 0%] [37. 5%] [25. 0%] [12. 5%] [0%] [-12. 5%] [-25. 0%] [-37. 5%] [-50. 0%] [-62. 5%] [-75. 0%] [-87. 5%] [-100%] Power Fast Ramp Response [Auto] Allows you to increase to enhance the response of the voltage regulator during the load transient. Configuration options: [Auto] [0. 00] - [1. 50] CPU Internal Power Saving Control Power Saving Level 1 Threshold [Auto] Lower value provides sufficient overclocking tolerance to enlarge the overclocking potential. Higher value provides better power-saving condition. Use <+> or <-> key to adjust the value. The values range from 0A to 80A at 1Amp increment. Power Saving Level 2 Threshold [Auto] Lower value provides sufficient overclocking tolerance to enlarge the overclocking potential. Higher value provides better power-saving condition. Use <+> or <-> key to adjust the value. The values range from 0A to 50A at 1Amp increment. Power Saving Level 3 Threshold [Auto] Lower value provides sufficient overclocking tolerance to enlarge the overclocking potential. [. . . ] Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The use of shielded cables for connection of the monitor to the graphics card is required to assure compliance with FCC regulations. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. ASUS MAXIMUS VI GENE A-1 Appendices IC: Canadian Compliance Statement Complies with the Canadian ICES-003 Class B specifications. This device complies with RSS 210 of Industry Canada. [. . . ]