User manual ASUS MY CINEMA-EHD3-100 QUICK START GUIDE

[. . . ] Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. · AMD, AthlonTM, K7, and/or combinations thereof are trademarks of Advanced Micro Devices, Inc. · VIA is a trademark of VIA Technologies, Inc. · Windows and MS-DOS are registered trademarks of Microsoft Corporation. [. . . ] H/W SETUP Connectors 01 01 01 Optional USB USBPORT 1 6 5 10 1: USB Power 2: USBP2­ 3: USBP2+ 4: GND 5: NC 6: USB Power 7: USBP3­ 8: USBP3+ 9: GND 3. HARDWARE SETUP 21) System Warning Speaker Connector (4-pin SPEAKER) This 4-pin connector connects to the case-mounted speaker. Two sources (LINE_OUT and SPEAKER) will allow you to hear system beeps and warnings. Only SPEAKER will allow you to hear system beeps before the integrated audio has been properly initialized. 22) System Power LED Lead (3-1 pin PWRLED) This 3-1 pin connector connects the system power LED, which lights when the system is powered on and blinks when it is in sleep mode. 23) System Message LED Lead (2-pin MSG. LED) This indicates whether a message has been received from a fax/modem. The LED will remain lit when there is no signal and blink when there is data received. This function requires an ACPI OS and driver support. 24) Reset Switch Lead (2-pin RESET) This 2-pin connector connects to the case-mounted reset switch for rebooting your computer without having to turn off your power switch. This is a preferred method of rebooting to prolong the life of the system's power supply. 25) ATX Power Switch Lead (2-pin PWRSW) The system power is controlled by a momentary switch connected to this lead. If you do not see anything within 30 seconds from the time you turn on the power, the system may have failed a power-on test. Recheck your jumper settings and connections or call your retailer for assistance. Award BIOS Beep Codes Beep One short beep when displaying logo Long beeps in an endless loop One long beep followed by three short beeps High frequency beeps when system is working Meaning No error during POST No DRAM installed or detected Video card not found or video card memory bad CPU overheated System running at a lower frequency ASUS MY CINEMA-EHD3-100 User's Manual 45 3. During power-on, hold down <Delete> to enter BIOS setup. * Powering Off your computer: You must first exit or shut down your operating system before switching off the power switch. For ATX power supplies, you can press the ATX power switch after exiting or shutting down your operating system. If you use Windows 9X, click the Start button, click Shut Down, and then click Shut down the computer?The power supply should turn off after Windows shuts down. NOTE: The message "You can now safely turn off your computer" will not appear when shutting down with ATX power supplies. 3. H/W SETUP Powering Up 46 ASUS MY CINEMA-EHD3-100 User's Manual 4. BIOS SETUP 4. 1 Managing and Updating Your BIOS 4. 1. 1 Upon First Use of the Computer System It is recommended that you save a copy of the original motherboard BIOS along with a Flash Memory Writer utility (AFLASH. EXE) to a bootable floppy disk in case you need to reinstall the BIOS later. AFLASH. EXE is a Flash Memory Writer utility that updates the BIOS by uploading a new BIOS file to the programmable flash ROM on the motherboard. [. . . ] Configuration options: [No] [Yes] Reset Configuration Data [No] The Extended System Configuration Data (ESCD) contain information about non-PnP devices. It can also hold the complete record of how the system was configured the last time it was booted. Select [Yes] only if you want to clear these data during the Power-On Self Test (POST). Configuration options: [No] [Yes] Boot Virus Detection [Enabled] This field allows you to set boot virus detection, ensuring a virus-free boot sector. [. . . ]