User manual ASUS NCLV-D

[. . . ] Motherboard NCLV-D (A) E1711 First Edition August 2004 Copyright © 2004 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. ("ASUS"). Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. ASUS PROVIDES THIS MANUAL "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. [. . . ] Devices communicate with an SMBus host and/or other SMBus devices using the SMBus interface. NCLV-D PSUSMB1 NCLV-D Power supply SMBus connector 2-32 PSU_I2CCLK PSU_I2CDATA NC GND +3. 3V Remote Sense Chapter 2: Hardware information GND I2C_6_DATA# +5V 1 2 . Parallel port connector (26-1 pin LPT1) This connector is for a parallel port. Connect the parallel port module cable to this connector, then install the module to a slot opening at the back of the system chassis. NCLV-D LPT1 Pin 1 STB# SPD0 SPD1 SPD2 SPD3 SPD4 SPD5 SPD6 SPD7 ACK# BUSY PE SLCT NCLV-D Parallel port connector 1 3 . BMC connector (16-pin BMCCONN1) This connector is for an ASUS server management card. NCLV-D BMCCONN1 +5VSB +5VSB BMC SMBDATA 12CDATA1 FP_PWRBTN# BMC_PRESENT# BMC_SMI# GND NCLV-D BMC connector ASUS NCLV-D (A) +5VSB +5VSB BMC SMBCLK 12CCLK1 PSON# BMC_RST# PWROK PSONEN# AFD# ERROR# PINIT# SLIN# GND GND GND GND GND GND GND GND 2-33 1 4 . System panel auxiliary connector (20-pin AUX_PANEL1) This connector supports several server system functions. NCLV-D AUX_PANEL1 CASEOPEN GND LOCATORLED1+ LOCATORLED1LOCATORBTN# GND LOCATORLED2LOCATORLED2+ +5VSB PIN1 NCLV-D Auxiliary panel connector · · · Chassis Intrusion connector (3-pin CASEOPEN) This lead is for a chassis with an intrusion detection feature. This requires an external detection mechanism such as a chassis intrusion sensor or microswitch. When you remove any chassis component, the sensor triggers and sends a high-level signal to this lead to record a chassis intrusion event. LAN1 link activity LED (2-pin LAN1_LINKACTLED) This 2-pin connector is for the LAN1 Activity LED. Connect the LAN1 Activity LED cable to this connector. This LED blinks during a network activity and is always lit when linked. LAN2 link activity LED (2-pin LAN2_LINKACTLED) This 2-pin connector is for the LAN2 Activity LED. Connect the LAN2 Activity LED cable to this connector. This LED blinks during a network activity and lights up when linked. Locator LED 1 (2-pin LOCATORLED1) This 2-pin connector is for the Locator LED 1. Connect the Locator LED 1 cable to this connector. This LED lights up when the Locator button is pressed and if there is no LAN1 connection (e. g. Locator LED 2 (2-pin LOCATORLED2) This 2-pin connector is for the Locator LED 2. Connect the Locator LED 2 cable to this connector. This LED is synchronized with the LAN2 LED. Locator Button/Switch (2-pin LOCATORBTN) This connector is for the locator button. This button queries the state of the system locator. Front Panel SMBus (6-1 pin) This connector allows you to connect SMBus (System Management Bus) devices. [. . . ] L i m i t e d allows changes only to selected fields, such as Date and Time. F u l l A c c e s s allows viewing and changing all the fields in the Setup utility. Change User Password Select this item to set or change the user password. The U s e r P a s s w o r d item on top of the screen shows the default N o t I n s t a l l e d After you set d. a password, this item shows I n s t a l l e d d. 4-34 Chapter 4: BIOS setup To set a User Password: 1. [. . . ]