User manual ASUS P4B533

[. . . ] P4B533 User Guide Motherboard E985 Checklist First Edition April 2002 Copyright © 2002 ASUSTeK COMPUTER INC. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. ASUS PROVIDES THIS MANUAL "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. [. . . ] · Refer to section "2. 5 System memory" for instruction on installing a DIMM. · Install a PCI VGA card into one of the PCI slots, or a 1. 5V AGP card into the AGP slot. · Make sure that your VGA/AGP card is not defective. · In JumperFree mode, check your CPU settings in BIOS and make sure you only set to the recommended settings. See section "4. 4 Advanced menu. " · In jumper mode, refer to section "2. 7 Switches and jumpers. " System failed memory test System failed VGA test System failed due to CPU over-clocking 3-2 Chapter 3: Powering up POST Message No keyboard detected Action · Check your keyboard if properly connected to the purple PS/2 connector on the rear panel. · See section "1. 4. 1 Major components" for the location of the connector. · Make sure you have connected a floppy disk to the floppy disk connector on the motherboard. · See section "2. 8 Connectors. " · Make sure you have connected an IDE hard disk drive to the one of the IDE connectors on the motherboard. · See section "2. 8 Connectors. " · Check CPU fan if working properly. · Check the CPU fan and make sure it turns on after you applied power to the system. · Check your power supply and make sure it is not defective. · Call ASUS technical support for assistance. See the "ASUS contact information" on page x. No floppy disk detected No IDE hard disk detected CPU temperature too high CPU fan failed CPU voltage out of range System completed Power-On Self Test · No action required Computer now booting from operating · No action required system You may disable the ASUS POST ReporterTM in the BIOS setup. See section "4. 4. 2 I/O Device Configuration". ASUS P4B533 motherboard user guide 3-3 3. 3 Powering off the computer You must first exit the operating system and shut down the system before switching off the power. For ATX power supplies, you can press the ATX power switch after exiting or shutting down the operating system. If you use Windows 95/98/2000/XP, click the Start button, click Shut Down, then click the OK button to shut down the computer. The power supply should turn off after Windows shuts down. The message "You can now safely turn off your computer" does not appear when shutting down with ATX power supplies. 3-4 Chapter 3: Powering up Chapter 4 This chapter tells how to change system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided. BIOS setup Chapter summary 4. 1 4. 2 4. 3 4. 4 4. 5 4. 6 4. 7 Managing and updating your BIOS . . . . . . . . . . . . . . 4-1 BIOS Setup program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7 Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10 Advanced Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-17 Power Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Prepare your message for each event. The total compressed size for all the wave files must not exceed 1Mbit, so make your messages as short as possible. 3. Use a recording software, such as Windows Recorder, to record your messages. It is recommended that you save your files in low quality to keep them small. For example, use 8-bit, mono quality at 22Khz sampling rate. You may want to create a separate folder for your wave files so you can locate them easily in one place. 5. [. . . ]