User manual ASUS P5GC-VM

[. . . ] IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners benefit, without intent to infringe. ii Contents Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Find the proper orientation and push down firmly until the connectors completely fit. · It is recommended that you use an ATX 12V Specification 2. 0-compliant Power Supply Unit (PSU) with a minimum of 350 W power rating. This PSU type has 24-pin and 4-pin power plugs. If you intend to use a PSU with 20-pin and 4-pin power plugs, make sure that the 20-pin power plug can provide at least 15A on +12V and that the PSU has a minimum power rating of 350 W. The system may become unstable or may not boot up without adequate power. Do not forget to connect the 4-pin ATX +12V power plug; otherwise, the system will not boot up. Use of a PSU with a higher power output is recommended when configuring a system with more power-consuming devices. The system may become unstable or may not boot up if the power is inadequate. The ATX 12V Specification 2. 0-compliant PSU passed the motherboard power requirement test with the following configuration: CPU : Memory : Graphics card : Parallel ATA devices : Serial ATA device : Optical drive : · Intel® Pentium® 4 3. 6 GHz 512 MB DDR (x 4) PCI Express x16 Nvidia® EN5900 IDE hard disk drive (x 2) SATA hard disk drive CD-ROM · · · · You must install a PSU with a higher power rating if you intend to install additional devices. ATX12V +12V DC GND ® EATXPWR +3 Volts +12 Volts +12 Volts +5V Standby Power OK Ground +5 Volts Ground +5 Volts Ground +3 Volts +3 Volts +12V DC GND P5GC-VM P5GC-VM ATX Power Connectors Ground +5 Volts +5 Volts +5 Volts -5 Volts Ground Ground Ground PSON# Ground -12 Volts +3 Volts ASUS P5GC-VM 1-31 8. Front panel audio connector (10-1 pin AAFP) This connector is for a chassis-mounted front panel audio I/O module that supports either HD Audio or legacy AC 97 audio standard. Connect one end of the front panel audio I/O module cable to this connector. Azalia-compliant pin definition GND PRESENCE# SENSE1_RETUR SENSE2_RETUR Legacy AC 97-compliant pin definition AGND NC NC NC ® AAFP P5GC-VM P5GC-VM Analog Front Panel Connector · · We recommend that you connect a high-definition front panel audio module to this connector to avail of the motherboard high-definition audio capability. If you want to connect a high-definition front panel audio module to this connector, make sure that the Azalia Controller item in the BIOS is set to [Enabled]. See page 2-25 for details. 9. Digital Audio connector (4-1 pin SPDIF_OUT) This connector is for the S/PDIF audio module to allow digital sound output. A Format 3 1/2 Floppy Disk window appears. Select Create an MS-DOS startup disk from the format options field, then click Start. Windows® 2000 environment To create a set of boot disks for Windows® 2000: a. Insert a formatted, high density 1. 44 MB floppy disk into the drive. Insert the Windows® 2000 CD to the optical drive. Click Start, then select Run. 2-2 Chapter 2: BIOS setup d. From the Open field, type D:\bootdisk\makeboot a: assuming that D: is your optical drive. Press <Enter>, then follow screen instructions to continue. Copy the original or the latest motherboard BIOS file to the bootable floppy disk. 2. 1. 2 ASUS EZ Flash utility The ASUS EZ Flash feature allows you to update the BIOS without having to go through the long process of booting from a floppy disk and using a DOS-based utility. The EZ Flash utility is built-in the BIOS chip so it is accessible by pressing <Alt> + <F2> during the Power-On Self-Test (POST). Visit the ASUS website (www. asus. com) to download the latest BIOS file for the motherboard and rename the file as P5GVMX. ROM. Save the BIOS file to a floppy disk, then restart the system. [. . . ] Install an Intel® Pentium® 4 CPU that supports the Intel® EM64T. Install a 64-bit operating system (Windows® XP Professional x64 Edition or Windows® Server 2003 x64 Edition). Install the 64-bit drivers for the motherboard components and devices from the support CD. Install the 64-bit drivers for expansion cards or add-on devices, if any. Refer to the expansion card or add-on device(s) documentation, or visit the related website, to verify if the card/device supports a 64-bit system. A. 2 Enhanced Intel SpeedStep® Technology (EIST) · The motherboard comes with a BIOS file that supports EIST. [. . . ]