User manual ASUS P5Q3 DELUXE WIFI-AP WIFI-AP@N

[. . . ] IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. ii Contents Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Loads the optimal settings for the system. When you choose this option, eXtreme Memory Profile item will show up 3-16 Chapter 3: BIOS setup 3. 4. 2 CPU Ratio Setting [Auto] Allows you to adjust the ratio between CPU Core Clock and FSB Frequency. Use the <+> and <-> keys to adjust the value. Configuration options: [Auto] [06. 0] [07. 0] [08. 0] [09. 0] The following two items appear only when you set the Ai Overclock Tuner item to [Manual]. FSB Frequency [XXX] Displays the frequency sent by the clock generator to the system bus and PCI bus. The value of this item is auto-detected by the BIOS. Use the <+> and <-> keys to adjust the FSB frequency. You can also type the desired CPU frequency using the numeric keypad. Refer to the table below for the correct Front Side Bus and CPU External Frequency settings. FSB/CPU External Frequency Synchronization Front Side Bus CPU External Frequency FSB 1600 400 MHz FSB 1333 333 MHz FSB 1066 266 MHz FSB 800 200 MHz PCIE Frequency [Auto] Allows you to set the PCI Express frequency. Use the <+> and <-> keys to adjust the PCIE frequency. The values range from 100 to 180. 3. 4. 3 FSB Strap to North Bridge [Auto] When set to [Auto], the FSB Strap will be adjusted automatically by FSB Frequency and DRAM Frequency. The values range from 0. 85000V to 2. 10000V* with a 0. 00625V interval. · Refer to the CPU documentation before setting the CPU Vcore voltage. Setting a high VCore voltage may damage the CPU permanently, and setting a low VCore voltage may make the system unstable. The value [2. 10000V] of the CPU Voltage item is supported only if the OV_CPU jumper is enabled, otherwise the maximum voltage supported is [1. 70000V]. CPU / Northbridge overvoltage setting on page 2-19 for details. · 3. 4. 13 CPU GTL Reference [Auto] Allows you to enable or setting CPU GTL reference. The values range from 0. 615V to 0. 667V. 3. 4. 14 CPU PLL Voltage [Auto] Allows you to set the CPU PLL voltage. The values range from 1. 5V to 2. 78V with a 0. 02V interval. 3. 4. 15 FSB Termination Voltage [Auto] Allows you to set the front side bus termination voltage. The values range from 1. 20V* to 1. 90V with a 0. 02V interval. The minimum value of this item becomes 1. 10V when a 45nm CPU is installed. 3. 4. 16 DRAM Voltage [Auto] Allows you to set the DRAM voltage. The values range from 1. 80V to 3. 08V with a 0. 02V interval. 3. 4. 17 NB Voltage [Auto] Allows you to set the North Bridge voltage. The values range from 1. 10V to 2. 20V* with a 0. 02V interval. ASUS P5Q3 DELUXE WIFI-AP DELUXE WIFI-AP 3-21 · The value [2. 20V] of the NB Voltage item is supported only if the OV_NB jumper is enabled, otherwise the maximum voltage supported is [1. 9V]. CPU / Northbridge overvoltage setting on page 2-19 for details. Setting the CPU PLL Voltage, FSB Termination Voltage, DRAM Voltage and NB Voltage items to a high level may damage the chipset, memory module and CPU permanently. [. . . ] The available stripe size values range from 16 KB to 128 KB. The default stripe size is 64 KB. We recommend a lower stripe size for server systems, and a higher stripe size for multimedia computer systems used mainly for audio and video editing. 7. 8. Enter the RAID volume capacity that you want and then press <Enter>. The default value indicates the maximum allowed capacity. [. . . ]