User manual ASUS P65UP8-SCSI

[. . . ] R P/I P65UP8 Symbios & Adaptec SCSI Utilities USER'S MANUAL This manual is divided into two sections · Section I - Symbios SCSI Utilities · Section II - Adaptec SCSI Utilities USER'S NOTICE No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. ASUS PROVIDES THIS MANUAL "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. [. . . ] No other actions are required to use these new drivers. You may want to review the command line options to insure you are using the best options for your configuration. ASUS P/I-P65UP8 User's Manual IV. NETWARE DRIVERS For NetWare v3. 12 New Installations NOTE: The SDMSNET3. DSK driver should work on a NetWare 3. 11 server. However, this compatibility is neither tested nor supported. Create a directory in which to install the NetWare file server. Change to that directory and copy all the files from the NetWare system disks into that directory. Copy the file SDMSNET3. DSK from the Symbios Logic device drivers diskette into this directory. If ASPI support is desired, also copy NETASPI3. NLM. To start NetWare and continue the installation, type: SERVER 4. When prompted, enter the name of the file server and network (IPX) number. See the chapter on file server installation in the NetWare Installation Manual for restrictions and further information. At the NetWare prompt, type: LOAD SDMSNET3 <options> This command loads the main driver. Without this command, NetWare is unable to access the hard disk drive. If ASPI support is desired, also type: LOAD NETASPI3 6. To bring up the Installation menu, at the NetWare prompt type: LOAD INSTALL Continue with the installation according to the file server installation chapter in the Novell NetWare Installation Manual. At the Available System Options menu, select the EDIT STARTUP. NCF option and check to see that the line LOAD SDMSNET3 is in the file. This eliminates the need to load drivers by hand every time the system is powered up. If the line appears more than once, remove the duplicate statements and all references to "port=xxxx", "slot=xxxx" and/or "mem=xxxx". In addition, if ASPI support is required, add the line: load NETASPI3. NLM to the file after the line: load SDMSNET3. DSK IV. NETWARE (Installation) 48 ASUS P/I-P65UP8 User's Manual IV. NETWARE DRIVERS For NetWare v4. xx New Installations 1. Begin the file server installation as per the instructions in the file server installation chapter in the Novell NetWare Installation Manual. [. . . ] (See the MSDOS documentation. ) Run afdisk from the DOS prompt only, not from the Windows MSDOS prompt. Before you run it, be sure the disk devices you want to format and partition are connected to the host adapter and that they are powered. Change to the directory where afdisk. exe is located (usually c:\scsi), type afdisk at the DOS prompt, and press Enter. Information about your SCSI disk devices appears on the screen. [. . . ]