User manual ASUS P7500

[. . . ] R AP7500 Pentium® II Corporate Server Hardware Reference Guide User's Notice No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. ASUS PROVIDES THIS MANUAL "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. [. . . ] A floppy drive spacer is used to cover the floppy drive and power button. A standard storage device spacer is used to cover the CD-ROM, tape drive, or additional CD-ROMs. You should purchase an extra spacer for each storage device. Floppy Drive Spacer Floppy and CD-ROM drive spacers Fixed Device Spacer Floppy drive with spacer Floppy and CD-ROM drives CD-ROM with spacer AP7500 Hardware Reference Guide II. System Components Hot-Swap Trays Maximum uptime in a server requires devices that can be easily replaced or "swapped. " The main hard disks are mounted in internal hot-swap trays for easy replacement. To remove the tray, unlock the tray and pull on the handle. A lock secures the handle and switches on or off the power to the hard drive. II. Components Hot-Swap Trays Removing or inserting the hot-swap tray Hot-Swap Tray (8 Total) Hot-Swap Tray Keylock Positions Lock/ Power On Unlock/ Power Off Hot-Swap Tray Interface The front of the hot-swap tray provides a keylock in order to switch the power on, which also locks the handle, and switch the power off, which also releases the handle. Two LEDs provide information on the power and activity status of the hard disk drive. When power is received by the hot-swap tray's connector board, the power LED will light. When data is written or read to or from the contained hard disk drive, the activity LED will flash proportional to the amount of data transferred. Air Inlet Activity LED (SLED) Keylock / Power Switch Power LED (PLED) Release / Transport Handle Hot-swap tray face plate 18 AP7500 Hardware Reference Guide II. System Components Hot-Swap Tray Usage Each hot-swap tray provides an aluminum carrier for a single SCSI hard disk drive with a maximum height of 1 5/8 inch, width of 4 inches, and length of 6 inches. The aluminum tray provides protection and maximum heat dissipation for almost all types of high speed SCSI disk drives. The provided cables and wires connect to the SCSI hard disk drive and screws are needed to secure the tray to the bottom of the SCSI hard disk drive. SCSI Cable Aluminum Tray Activity LED (ALED) Power Connector Screw Holes SCSI ID Hot-swap tray and its connectors Hot-Swap Tray Front Connections The hot-swap tray provides wires for connecting the activity LED, power LED, SCSI ID, power, and SCSI signal. Connect the 8 pin connector to the SCSI Address pins according to the colors shown. Connect the 2 pin connector to the activity signal pins according to the colors shown. IMPORTANT: The following is only an example. Always consult your hard disk drive documentation or labels for the exact wiring specific to your hard disk drive make and model. Seagate Cheetah (ST34501W) side opposite power & SCSI Orange White Green Brown Red Pin 1 Unused Black Activity Signal 8 Blue 4 Yellow 2 Red 1 Black Pin 2 SCSI Address (ID#) Hot-swap tray SCSI ID & activity LED wires connected (Seagate HD) AP7500 Hardware Reference Guide 19 II. System Components Hot-Swap Tray Connector Board The connector board is mounted on the hot-swap tray to interface with the SCSI backplane in the chassis. The connector board combines all the signal and power into one docking connector for a simple hot-swap unit. KEY SLED (not used) PLED ALED_IN (not used) SCSI_ID II. Components Hot-Swap Connector 20 Hot-Swap Tray Docking Connector Wide SCSI Connector Hard Disk Drive Power Connector Hot-swap tray connector board parts Hot-Swap Tray Rear Connections KEY: These 2 pins connect to the keylock on the tray's front panel to turn on and off the drive's power. PLED: These 2 pins connect to the power LED on the tray's front panel to show when the connector board receives power. SCSI_ID: These 8 pins connect to the hard disk drive's SCSI address pins to set the SCSI ID number of the hard disk drive. [. . . ] Each LPT port is configured to use a different IRQ and address assignment. PCI Bus (Peripheral Component Interconnect Local Bus) PCI bus is a specification that defines a 32-bit data bus interface. PCI is a standard widely used by expansion card manufacturers. Appendix Glossary 36 AP7500 Hardware Reference Guide III. [. . . ]