User manual ASUS P8H67-I PRO

[. . . ] The author assumes no responsibility for any errors or omissions that may appear in this document nor does the author make a commitment to update the information contained herein. Mother Board 8S648FXP-RZ Motherboard 8S648FXP-RZ Nov. 3, 2004 Preparing Your Computer Computer motherboards and expansion cards contain very delicate Integrated Circuit (IC) chips. To protect them against damage from static electricity, you should follow some precautions whenever you work on your computer. Unplug your computer when working on the inside. [. . . ] Access Mode Use this to set the access mode for the hard drive. The four options are: CHS/LBA/Large/Auto(default:Auto) Hard drive information should be labeled on the outside drive casing. Enter the appropriate option based on this information. Cylinder Number of cylinders Head Number of heads Precomp Write precomp Landing Zone Landing zone Sector Number of sectors If a hard disk has not been installed, select NONE and press <Enter>. - 21 - BIOS Setup English Drive A / Drive B The category identifies the types of floppy disk drive A or drive B that has been installed in the computer. None No floppy drive installed 360K, 5. 25" 5. 25 inch PC-type standard drive; 360K byte capacity. 1. 2M, 5. 25" 5. 25 inch AT-type high-density drive; 1. 2M byte capacity (3. 5 inch when 3 Mode is Enabled). 720K, 3. 5" 3. 5 inch double-sided drive; 720K byte capacity 1. 44M, 3. 5" 3. 5 inch double-sided drive; 1. 44M byte capacity. 2. 88M, 3. 5" 3. 5 inch double-sided drive; 2. 88M byte capacity. Floppy 3 Mode Support (for Japan Area) Disabled Drive A Drive B Both Normal Floppy Drive. (Default value) Drive A is 3 mode Floppy Drive. Drive A & B are 3 mode Floppy Drives. Halt on The category determines whether the computer will stop if an error is detected during power up. No Errors The system boot will not stop for any error that may be detected and you will be prompted. to 3 Init Display First Select the first initation of monitor or display from AGP or PCI VGA card. (Default value) PCI Set Init display first to PCI. 8S648FXP-RZ Series Motherboard - 24 - Integrated Peripherals CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Integrated Peripherals IDE1 Conductor Cable IDE2 Conductor Cable On-Chip Primary PCI IDE On-Chip Secondary PCI IDE AC97 Audio Onboard LAN device * USB Controller USB Legacy Support SiS Serial ATA Controller SiS Serial ATA Mode Onboard Serial Port 1 Onboard Serial Port 2 Onboard Parallel Port Parallel Port Mode ECP Mode Use DMA [Auto] [Auto] [Enabled] [Enabled] [Enabled] [Enabled] [Enabled] [Disabled] [Enabled] [RAID] [3F8/IRQ4] [2F8/IRQ3] [378/IRQ7] [ECP] [3] Item Help Menu Level [Auto] Auto-detect IDE cable type [ATA66/100/133] Set Conductor cable to ATA66/100/133(80 Pins) [ATA33] Set Conductor cable to ATA33(40-Pins) English : Move Enter: Select F5: Previous Values +/-/PU/PD: Value F10: Save F6: Fail-Save Defaults ESC: Exit F1: General Help F7: Optimized Defaults IDE1 Conductor Cable Auto ATA66/100/133 ATA33 Will be automatically detected by BIOS. (Default value) Set IDE1 Conductor Cable to ATA66/100/133 (Please make sure your IDE device and cable is compatible with ATA66/100/133). Set IDE1 Conductor Cable to ATA33 (Please make sure your IDE device and cable is compatible with ATA33). IDE2 Conductor Cable Auto Will be automatically detected by BIOS. (Default value) ATA66/100/133 Set IDE2 Conductor Cable to ATA66/100/133 (Please make sure your IDE device and cable is compatible with ATA66/100/133). ATA33 Set IDE2 Conductor Cable to ATA33 (Please make sure your IDE device and cable is compatible with ATA33). On-Chip Primary PCI IDE Enabled Disabled Enabled Disabled Enable onboard 1st channel IDE port. (Default value) Disable onboard 1st channel IDE port. (Default value) Disable onboard 2nd channel IDE port. Enable onboard AC'97 audio function. (Default value) On-Chip Secondary PCI IDE AC97 Audio Enabled Disabled Disabled Enabled Onboard LAN device * "*" Only for 8S648FXP-RZ. - 25 - BIOS Setup English USB Controller Enabled Disabled Enable USB Controller. (Default value) Disable USB Controller. USB Legacy Support When USB keyboard or mouse is installed, please set at Enabled. [. . . ] Support : http://tw. giga-byte. com/TechSupport/ServiceCenter. htm Non-Tech. Support(Sales/Marketing) : http://ggts. gigabyte. com. tw/nontech. asp WEB address (English): http://www. gigabyte. com. tw WEB address (Chinese): http://chinese. giga-byte. com U. S. A. Address: 17358 Railroad St, City of Industry, CA 91748. TEL: +1 (626) 854-9338 FAX: +1 (626) 854-9339 Tech. [. . . ]