User manual ASUS P8Z77-V

[. . . ] No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. Offer to Provide Source Code of Certain Software This product may contain copyrighted software that is licensed under the General Public License ("GPL") and under the Lesser General Public License Version ("LGPL"). [. . . ] Configuration options: [Enabled][Disabled] Change Settings [IO=3F8h; IRQ=4] Allows you to select the Serial Port base address. 7 APM EFI BIOS Utility - Advanced Mode Exit Main Back ErP Ready Restore AC Power Loss Power On By PCI Power On By PCIE Power On By Ring Power On By RTC Ai Tweaker Advanced\ APM > Advanced Monitor Boot Tool Disabled Power Off Disabled Disabled Disabled Disabled Allow BIOS yo switch off some power at S5 to get the system ready for ErP requirement. When set to Enabled, all other PME options will be switched off. ErP Ready [Disabled] This item allows user to switch off some power at S5 to get the system ready for ErP requirement. When set enabled to Enabled, all other PME options will be switched off. Configuration options: [Disabled] [Enabled] Restore AC Power Loss [Power Off] [Power On] [Power Off] [Last State] The system goes into on state after an AC power loss. The system goes into off state after an AC power loss. The system goes into either off or on state, whatever the system state was before the AC power loss. Disables the PCI devices to generate a wake-on-LAN feature of the Intel/ Realtek LAN device. Enables the PCI devices to generate a wake-on-LAN feature of the Intel/ Realtek LAN device. Disables the PCIE devices to generate a wake-on-LAN feature of the Intel/Realtek LAN device. Enables the PCIE devices to generate a wake-on-LAN feature of the Intel/ Realtek LAN device. Disables the serial port (COM1) devices to generate a wake event. Enables the serial port (COM1) devices to generate a wake event. Power On By PCI [Disabled] [Disabled] Chapter 3 3-26 [Enabled] Power On By PCIE [Disabled] [Disabled] [Enabled] Power On By Ring [Disabled] [Disabled] [Enabled] [Disabled] [Enabled] Power On By RTC [Disabled] Disables RTC to generate a wake event. When set to [Enabled], the items RTC Alarm Date (Days) and Hour/ Minute/Second will become user-configurable with set values. 6 Monitor menu The Monitor menu displays the system temperature/power status, and allows you to change the fan settings. Scroll down to display the following items: Chapter 3 3-28 Chapter 3: BIOS setup CPU Temperature / MB Temperature [xxxºC/xxxºF] The onboard hardware monitor automatically detects and displays the CPU and motherboard temperatures. Select Ignore if you do not wish to display the detected temperatures. CPU Fan Speed [xxxx RPM] or [Ignore] / [N/A] CPU OPT Speed [xxxx RPM] or [Ignore] / [N/A] Chassis Fan 1/3 Speed [xxxx RPM] or [Ignore] / [N/A] The onboard hardware monitor automatically detects and displays the CPU, chassis, and power fan speed in rotations per minute (RPM). If the fan is not connected to the motherboard, the field shows N/A. Select Ignore if you do not wish to display the detected speed. [. . . ] Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. iC: Canadian Compliance Statement Complies with the Canadian ICES-003 Class B specifications. This device complies with RSS 210 of Industry Canada. This Class B device meets all the requirements of the Canadian interference-causing equipment regulations. [. . . ]