User manual ASUS PCH-DL

[. . . ] PCH-DL User Guide Motherboard E1571 Checklist First edition V1 April 2004 Copyright © 2004 ASUSTeK COMPUTER INC. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. ASUS PROVIDES THIS MANUAL "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. [. . . ] If you wish to use the chassis intrusion detection feature, remove the jumper cap from the pins. CHASSIS1 Chassis Signal GND (Default) PCH-DL PCH-DL Chassis Intrusion Connector 9. IEEE 1394 connector (10-1 pin IEEE1394_1) This connector is for a 1394 module. Attach the 10-1 pin 1394 cable plug from the module to this connector. You may also connect a 1394compliant internal hard disk to this connector. +5VSB_MB IEEE1394_1 PCH-DL IEEE-1394 Connector TPA0+ GND TPB0+ +12V PCH-DL 1 2-28 Chapter 2: Hardware information TPA0GND TPB0+12V GND 10. CPU, chassis, and system fan connectors (3-pin CHA_FAN1, CPU_FAN1/2, SYS_FAN1/2/3) The fan connectors support cooling fans of 350mA~740mA (8. 88W max. ) or a total of 1A~2. 22A (26. 64W max. ) at +12V. Connect the fan cables to the fan connectors on the motherboard, making sure that the black wire of each cable matches the ground pin of the connector. CHA_FAN1 GND +12V Rotation CPU_FAN1 Rotation +12V CPU_FAN2 GND SYS_FAN1 GND +12V Rotation Rotation +12V GND PCH-DL SYS_FAN2 SYS_FAN3 PCH-DL 12-Volt Fan Connectors Do not forget to connect the fan cables to the fan connectors. Lack of sufficient air flow within the system may damage the motherboard components. DO NOT place jumper caps on the fan connectors! 11. Digital audio connector (4-1 pin SPDIF_O1) This S/PDIF Out connector is available for an S/PDIF audio module. Connect one end of the S/PDIF audio cable to this connector and the other end to the S/PDIF module. SPDIF_01 PCH-DL PCH-DL Digital Audio Connector ASUS PCH-DL motherboard +5V SPDIFOUT GND 2-29 12. GAME/MIDI connector (16-1 pin GAME1) This connector supports a GAME/MIDI module. Connect the GAME/ MIDI cable to this connector. The GAME/MIDI port on the module connects a joystick or a game pad for playing games, and MIDI devices for playing or editing audio files. GAME1 PCH-DL PCH-DL Game Connector 13. Internal audio connectors (4-pin CD1, AUX1, MODEM1) These connectors allow you to receive stereo audio input from sound sources such as a CD-ROM, TV tuner, or MPEG card. The MODEM connector allows the onboard audio to interface with a voice modem card with a similar connector. It also allows the sharing of mono_in (such as a phone) and a mono_out (such as a speaker) between the audio and a voice modem card. Right Audio Channel Ground Ground Left Audio Channel MIDI_IN J2B2 J2CY MIDI_OUT J2CX J2B1 +5V +5V J1B2 J1CY GND GND J1CX J1B1 +5V PCH-DL MODEM1 Modem-Out Ground Ground Modem-In CD1 (Black) AUX1 (White) PCH-DL Internal Audio Connectors 2-30 Chapter 2: Hardware information Right Audio Channel Ground Ground Left Audio Channel 14. Front panel audio connector (10-1 pin FP_AUDIO1) This is an interface for the Intel front panel audio cable that allow convenient connection and control of audio devices. By default, the pins labeled LINE OUT_R/BLINE_OUT_R and the pins LINE OUT_L/BLINE_OUT_L are shorted with jumper caps. Remove the caps only when you are connecting the front panel audio cable. FP_AUDIO1 MIC2 MICPWR Line out_R NC Line out_L AGND +5VA BLINE_OUT_R BLINE_OUT_L PCH-DL PCH-DL Intel Panel Connector 15. Hard disk activity LED (2-pin IDE_LED1) This connector supplied power to the hard disk activity LED. The read or write activities of any device connected to the primary or secondary IDE connector cause this LED to light up. IDE_LED1 -+ PCH-DL PCH-DL IDE Activity LED TIP: If the case-mounted LED does not light up, try reversing the 2-pin plug. ASUS PCH-DL motherboard 2-31 16. System panel connector (20-pin PANEL) This connector accommodates several system front panel functions. Speaker Connector +5V HD_LED+ HD_LEDSpeaker Power LED PLED+ LAN_LINK PLEDLAN_ACT +5VSB MLED Message LED PCH-DL Reset SW ATX Power Switch* PCH-DL System Panel Connector * Requires an ATX power supply. · System Power LED (3-pin PLED) This lead connects to the system power LED. [. . . ] Set to [Enabled] to configure the Type Rate and Type Delay items. Configuration options: [Disabled] [Enabled] The items Typematic Rate (Chars/Sec) and Typematic Delay become configurable only when the item Typematic Setting is enabled. Typematic Rate (Chars/Sec) [6] Allows you to select the rate at which character repeats when you hold a key. Configuration options: [6] [8] [10] [12] [15] [20] [24] [30] Typematic Delay (Msec) [250] Allows you to set the delay before key strokes begin to repeat. Configuration options: [250] [500] [750] [1000] 4. 6. 5 Security Security Supervisor Password User Password Password Check Clear Clear [Setup] Select Menu Item Specific Help Supervisor password control full access. ASUS PCH-DL motherboard 4-35 Supervisor Password [Clear] User Password [Clear] These fields allow you to set passwords. [. . . ]