User manual ASUS PCI-AS300

[. . . ] R PCI-AS300 SCSI/Audio MediaBus Card USER'S MANUAL USER'S NOTICE No part of this product, including the product and software may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form by any means without the express written permission of ASUSTeK COMPUTER INC. (hereinafter referred to as ASUS) except documentation kept by the purchaser for backup purposes. ASUS provides this manual "as is" without warranty of any kind, either express or implied, including but not limited to the implied warranties or conditions of merchantability or fitness for a particular purpose. In no event shall ASUS be liable for any loss or profits, loss of business, loss of use or data, interruption of business, or for indirect, special, incidental, or consequential damages of any kind, even if ASUS has been advised of the possibility of such damages arising from any defect or error in this manual or product. [. . . ] · ASUS PCI-AS300 User's Manual R PCI-AS300 SCSI/Audio MediaBus Card USER'S MANUAL Adaptec SCSI Drivers & Utilities (This page was intentionally left blank) 14 ASUS PCI-AS300 User's Manual IV. ADAPTEC SCSI SELECT Configuring the SCSI Adapter Access the SCSI BIOS by holding down both CTRL and A keys when you see the BIOS banner message listing the driver name and the attached devices. For example: Adaptec AIC-7880 Ultra/Wide W BIOS v1. 24 (c) 1996 Adaptec, Inc. <<< Press <Ctrl><A> for SCSISelect(TM) Utility!>>> The SCSISelect screen will come up. Instructions on how to move the cursor and select options are listed on the bottom of the program windows. You can select either Configure/View Host Adapter Settings or SCSI Disk Utilities. Configure/View Host Adapter Settings Host Adapter SCSI Termination. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Low ON/High ON · When using 50-Pin connector only, choose "Low ON/High ON" (Default) · When using 68-Pin connector only, choose "Low ON/High ON" (Default) · When using both 50-Pin & 68-Pin, choose "Low OFF/High ON" IV. SCSI SELECT (Configuring Adapter) 15 Select the default of "Low ON/High ON" and press Enter, then use the up and down arrows to make your new selection and press Enter. Press ESC to go back to the Options menu. Press ESC again and select Yes to exit the program. SCSI Disk Utilities The SCSI Disk Utilities option displays information on SCSI IDs 0 though 15, listing all devices on the bus including non-disk devices. When you select a device from the list and press Enter key, another window appears giving you the option of selecting one of two sub-utilities, Format Disk or Verify Media. These utilities are used for hard disk drives only and will have no effect on other non-disk SCSI devices. Format Disk - is a SCSI low-level formatting utility. In general, SCSI hard drive have already been low-level formatted when you get them, so you generally should not need to use this function. Verify Media - scans the selected drive media for defects, notifies you of any found and gives you the option of reassigning bad blocks so that data will not be written to them. This is only necessary if you suspect that your SCSI disk drive has a problem. ASUS PCI-AS300 User's Manual (This page was intentionally left blank) 16 ASUS PCI-AS300 User's Manual IV. ADAPTEC EZ-SCSI UTILITY Welcome to Adaptec EZSCSI® 4. 00e Adaptec EZSCSI gives you what you need to use your SCSI devices most effectively with Windows®95 and WindowsNTTM. You can also use Adaptec EZSCSI on computers running DOS, Windows®3. 1x, or Windows for Workgroups3. 1x. Quick Start Instructions First, install SCSI devices (see the hardware documentation for details). Then follow the instructions for your operating system software in one of the following sections. We recommend that after you install Adaptec EZSCSI you run SCSITutor to learn more about the features of SCSI. Windows95 or WindowsNT If you want to install Windows95 or WindowsNT on a new computer system, you may not be able to access your SCSI CDROM drive at first. (Usually, you install Windows95 and WindowsNT from a CDROM disc. ) To gain access to your CDROM drive, follow the DOS Quick Start instructions. Then reboot your computer and follow these instructions: 1 Install Windows95 or WindowsNT version 3. 51 or above, and start it running on your computer. [. . . ] Pressing <ENTER> at the above screen will show the installation paths. You may change the paths or press <ENTER> again if the paths are correct. Press <ENTER> to continue so that changes can be made to you system files. Win3. 1x Audio Driver (Audio Installation) 8 You will be prompted that an addition will be made in your C:\AUTOEXEC. BAT and C:\CONFIG. SYS files. The typical PC will have these settings added to the system files: C:\AUTOEXEC. BAT SET BLASTER=A220 I5 D1 H5 P330 T6 SET SOUND=C:\VIBRA16 SET MIDI=SYNTH:1 MAP:E C:\VIBRA16\DIAGNOSE /S /W=C:\WINDOWS C:\VIBRA16\MIXERSET /P /Q C:\CONFIG. SYS FILES=40 (If less than 40 or does not exist) If you wish to use the "Play" and "Record" utility located in \VIBRA16\ directory in DOS mode, you must also add the following two lines through "Custom Installation. " DEVICE=C:\VIBRA16\DRV\VIBRA16. SYS /UNIT=0 /BLASTER=A:220 I:5 D:1 H:5 DEVICE=C:\VIBRA16\DRV\CTMMSYS. SYS ASUS PCI-AS300 User's Manual VIII. [. . . ]