User manual ASUS PP-DLW

[. . . ] PP-DLW User Guide Motherboard E1173 Checklist First Edition V1 January 2003 Copyright © 2003 ASUSTeK COMPUTER INC. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. ASUS PROVIDES THIS MANUAL "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. [. . . ] It also allows the sharing of mono_in (such as a phone) and a mono_out (such as a speaker) between the audio and a voice modem card. AUDIO_COM2 (White) Left Audio Channel Ground Ground Right Audio Channel Ground SMBDATA +5V AUDIO_COM1 (Black) PP-DLW PP-DLW Internal Audio Connectors 2-24 Chapter 2: Hardware information 14. Wake-On-Ring Connector (2-pin J18) This connector connects to internal modem cards with a Wake-OnRing output. The connector wakes up the system when a ringup packet or signal is received through the internal modem card. For external modems, Wake-On-Ring is detected through the COM port. J18 Ground Ring# 12 PP-DLW PP-DLW Wake-On-Ring Connector 15. System panel connector (20-pin PANEL) This connector accommodates several system front panel functions. Keylock Power LED PLED Keylock Ground +5VSB Speaker Connector +5V Ground Ground Speaker +5 V MLED ExtSMI# Ground PWR Ground Message LED PP-DLW Reset SW ATX Power Switch* SMI Lead PP-DLW System Panel Connectors * Requires an ATX power supply. ASUS PP-DLW motherboard user guide Reset Ground 2-25 · System Power LED Lead (3-1 pin PLED) This 3-1 pin connector connects to the system power LED. The LED lights up when you turn on the system power, and blinks when the system is in sleep mode. · System Message LED Lead (2-pin MLED) This 2-pin connector is for the system message LED that indicates receipt of messages from a fax/modem. The normal status for this LED is OFF, when there is no incoming data signal. The system message LED feature requires an ACPI OS and driver support. · System Warning Speaker Lead (4-pin SPEAKER) This 4-pin connector is for a chassis-mounted speaker. · ATX Power Switch / Soft-Off Switch Lead (2-pin PWR) This lead connects a switch that controls the system power. Pressing the power switch turns the system between ON and SLEEP, or ON and SOFT OFF, depending on the BIOS or OS settings. Pressing the power switch while in the ON mode for more than 4 seconds turns the system OFF. · Reset Switch Lead (2-pin RESET) This lead connects to the case-mounted reset switch for rebooting the system without turning off the system power. · System Management Interrupt Lead (2-pin SMI) This lead connects to the case-mounted suspend switch, and allows you to manually place the system into "Suspend Mode" or "Green Mode" where system activity is decreased to save electricity and expand the life of system components. · Keylock Lead (2-pin KEYLOCK) This lead connects to a chassis-mounted switch to allow use of the keyboard lock feature. 2-26 Chapter 2: Hardware information Chapter 3 This chapter describes the power up sequence and gives information on the BIOS beep codes. Powering up Chapter summary 3. 1 3. 2 Starting up for the first time . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 Powering off the computer . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 ASUS PP-DLW motherboard 3. 1 Starting up for the first time 1. After making all the connections, replace the system case cover. Connect the power cord to the power connector at the back of the system chassis. Connect the power cord to a power outlet that is equipped with a surge protector. Turn on the devices in the following order: a. External SCSI devices (starting with the last device on the chain) c. [. . . ] When asked for the installation media, choose `media images', and type the directory path to the VOL. 000. 000 file. (In step 1, if you copied it to /tmp, type `/tmp'). After the installation of the driver is complete, exit `custom'. Run `netconfig' and add the adapters. [. . . ]