User manual ASUS PRL-DLS533

[. . . ] PRL-DLS533 Dual Intel® XeonTM-based Motherboard ServerWorks® GCSL SystemSet ® E1223 PRL-DLS533 E1223 User Guide PRL-DLS533 User Guide Motherboard E1223 Checklist First Edition March 2003 Copyright © 2003 ASUSTeK COMPUTER INC. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. ASUS PROVIDES THIS MANUAL "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. [. . . ] You will then be prompted to "Press F1 to continue or DEL to enter SETUP". 4-26 Chapter 4: BIOS Setup 4. 6 Boot Menu The motherboard BIOS supports the BIOS Boot Specification (BBS) version 1. 01. BBS is an intelligent mechanism that provides flexible ways to set boot sequence for Initial Program Load (IPL) devices such as CD-ROMs, network remote boot ROM, and SCSI or RAID controllers on PnP cards. The IPL devices are classified into three categories: BIOS Aware IPL Devices (BAID) Legacy devices PnP devices, includes Boot Connection Vector (BCV) and Bootstrap Entry Vector (BEV) devices ASUS PRL-DLS533 motherboard user guide 4-27 1st Boot : (BAID) [None] This field allows you to select a BIOS Aware IPL Devices (BAID) to boot from. A BAID is any device that can boot on an operating system but requires a specific BIOS code for support. Bootable FDDs, ATA HDD, ATAPI CD-ROM, ATA ZIP, and ATA MO drives are classified as BAID. The drives present in the system will appear as options for this field. 2nd Boot : (Legacy) [Disabled] This field reserves the boot sequence selection only to legacy devices including FDD, HDD, CD-ROM, SCSI, and LAN. This mode does not allow booting from a boot device on an add-on card or controller. If you wish to assign a device as a 1st Boot device for a specific application, you must set that legacy device at the 1st Boot sequence. For this motherboard, the following options are present onboard: [Disabled] [Floppy] [HDD] [CD-ROM] [LAN Option ROM] [SCSI] 3rd Boot : (BCV) [None] This field allows you to select a Boot Connection Vector (BCV) device to boot from. BCV devices include SCSI controllers or SCSI cards, RAID cards, and other devices on add-on cards with option ROM that hooks INT 13 to BIOS. The BCV devices present in the system will appear as options for this field. The field shows [None] if no BCV device is installed. Some SCSI RAID cards hook INT 19 to BIOS. If you use these cards, you should enable INT 19 after installing the card. Otherwise, you will not be able to enter the RAID card BIOS. 4th Boot : (BEV) [<0> Intel Corporation] This field allows you to select a Bootstrap Entry Vector (BEV) device to boot from. BEV devices include network controllers or cards. The BEV devices present in the system will appear as options for this field. For this motherboard, the following options are present onboard: [None] Plug & Play O/S [No] This field allows you to use a Plug-and-Play (PnP) operating system to configure the PCI bus slots instead of using the BIOS. When [Yes] is selected, interrupts may be reassigned by the OS. If you installed a nonPnP OS or if you want to prevent reassigning of interrupt settings, keep the default setting [No]. Configuration options: [No] [Yes] 4-28 Chapter 4: BIOS Setup Reset Configuration Data [No] The Extended System Configuration Data (ESCD) contain information about non-PnP devices. It also holds the complete record of how the system was configured the last time it was booted. [. . . ] If you are downloading the latest driver from the Intel website, save the package to a directory on your system; for example, the /tmp directory. You can install the driver from this directory or spool the driver from the directory so the driver resides on the system. Example of installing the driver from the directory: pkgadd ­d /<dir_location>/e1008g. pkg Example of spooling the driver from the directory to the system: pkgadd -s spool ­d /<dir_location>/e1008g. pkg e1008g pkgadd e1008g 5. 7. 3 ATI® Rage XL Display Driver Installation SCO UnixWare 7. 1. 1 system can correctly recognize ATI Rage XL graphic controller (ATI MACH64) during installation. User doesn't need to load or modify the video driver for the onboard VGA device. 5-54 Chapter 5: Driver installation 5. 8 Linux RedHat 7. 3/8. 0 5. 8. 1 LSI® SCSI Driver Installation The The Fusion-MPT driver is a bundled boot controller for RedHat 7. 3/ 8. 0. [. . . ]