User manual ASUS PTGD1-LA PUFFER M-UL8E

[. . . ] If the instructions in this section do not match the CPU documentation, follow the latter. Upon purchase of the motherboard, make sure that the PnP cap is on the socket and the socket contacts are not bent. Contact your retailer immediately if the PnP cap is missing, or if you see any damage to the PnP cap/socket contacts/motherboard components. ASUS will shoulder the cost of repair only if the damage is shipment/ transit-related. [. . . ] Align a DIMM on the socket such that the notch on the DIMM matches the break on the socket. 1 DDR DIMM notch 1 2. Unlocked retaining clip A DDR DIMM is keyed with a notch so that it fits in only one direction. DO NOT force a DIMM into a socket to avoid damaging the DIMM. 3. Firmly insert the DIMM into the socket until the retaining clips snap back in place and the DIMM is properly seated. Locked Retaining Clip 3. 3 Removing a DDR DIMM 2 To remove a DIMM: 1. Simultaneously press the retaining clips outward to unlock the DIMM. 1 1 DDR DIMM notch Support the DIMM lightly with your fingers when pressing the retaining clips. The DIMM might get damaged when it flips out with extra force. 2. Remove the DIMM from the socket. ASUS PTGD1-LA (Puffer M-UL8E) 7 4. Expansion slots The motherboard has one PCI Express and three PCI slots. To install and configure an expansion card: 1. Install an expansion card following the instructions that came with the chassis. Turn on the system and change the necessary BIOS settings, if any. Install the drivers and/or software applications for the expansion card according to the card documentation. Standard interrupt assignments IRQ 0 1 2 3 3 3 3 5 5 5 5 5 5 6 7 8 9 10 10 10 10 10 11 11 11 12 13 14 14 Standard Function System Timer Standard 101/102-key or Microsoft® Natural PS/2 Keyboard Programmable Interrupt Controller AHPC IRQ Holder for PCI IRQ Steering Intel® 82801FB/FBM PCI Express Root Port-2660 Intel® 82801FB/FBM USB Universal Host Controller-265B Intel® i915P MCH AHPC IRQ Holder for PCI IRQ Steering AHPC IRQ Holder for PCI IRQ Steering Realtek® TRL8139/810x Family Fast Ethernet NIC Intel® 82801FB/FBM PCI Express Root Port-2662 Intel® 82801FB/FBM USB Universal Host Controller-2658 Intel® 82801FB/FBM USB2 Enhanced Host Controller-265C Standard Floppy Disk Controller ECP Printer Port (LPT1) System CMOS/Real Time Clock SCI IRQ used by ACPI Bus AHPC IRQ Holder for PCI IRQ Steering AHPC IRQ Holder for PCI IRQ Steering VIA OHCI Compliant IEEE 1394 Host Controller Intel® 82801FB/FBM PCI Express Root Port-2666 Intel® 82801FB/FBM Ultra ATA Storage Controllers-2659 AHPC IRQ Holder for PCI IRQ Steering Intel® 82801FB/FBM PCI Express Root Port-2664 Intel® 82801FB/FBM USB Universal Host Controller-265A Microsoft® Port Mouse Numeric Data Processor Intel® 82801FB/FBM Ultra ATA Storage Controllers-266F Intel® 82801FB Ultra ATA Storage Controllers-2652 8 ASUS PTGD1-LA (Puffer M-UL8E) IRQ assignments for this motherboard A PCI slot 1 PCI slot 2 PCI slot 3 Onboard LAN Onboard 1394 controller -- shared -- -- -- B -- -- used -- -- C -- -- -- -- -- D shared -- -- -- -- E -- -- -- -- used F -- -- -- used -- PCI Express slot This motherboard has one PCI Express slot, which supports a 164-pin x16 interface graphics card. PCI slots There are three 32-bit PCI slots on this motherboard. The slots support PCI cards such as a LAN card, SCSI card, USB card, and other cards that comply with PCI specifications. ASUS PTGD1-LA (Puffer M-UL8E) 9 5. Jumpers This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in CMOS, which include system setup information such as system passwords. Turn OFF the computer and unplug the power cord. Move the jumper cap from pins 2-3 (Normal) to pins 1-2 (Clear CMOS). Keep the cap on pins 2-3 for about 5~10 seconds, then move the cap back to pins 2-3. Plug the power cord and turn ON the computer. Hold down the <Del> key during the boot process and enter BIOS setup to re-enter data. These two 4-pin Universal Serial Bus (USB) ports are available for connecting USB 2. 0 devices. These two 4-pin Universal Serial Bus (USB) ports are available for connecting USB 2. 0 devices. C o a x i a l S / P D I F O u t p o r t . This port connects an external audio output device via a coaxial S/PDIF cable. This port connects an external audio input device via a coaxial S/PDIF cable. P S / 2 k e y b o a r d p o r t ( p u r p l e ) . [. . . ] Connect the chassis power LED cable to this connector. The system power LED lights up when you turn on the system power, and blinks when the system is in sleep mode. Hard disk drive activity This 2-pin connector is for the HDD Activity LED. Connect the HDD Activity LED cable to this connector. [. . . ]