User manual ASUS RAMPAGE II EXTREME

[. . . ] If this Eric Lu equipment does cause interference to radio or television equipment reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: DECLARATION OF CONFORMITY Per FCC Part 2 Section 2. Address: 18305 Valley Blvd. , Suite#A LA Puent, CA 91744 Phone/Fax No: (818) 854-9338/ (818) 854-9339 hereby declares that the product Product Name: Mother Board Model Number: GA-6VM7-4I Conforms to the following specifications: FCC Part 15, Subpart B, Section 15. 107(a) and Section 15. 109(a), Class B Digital Device Supplementary Information: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful and (2) this device must accept any inference received, including that may cause undesired operation. ERIC LU Representative Person's Name: Signature: Date: Feb. [. . . ] You can run anti-virus program to locate the problem. Enabled Activate automatically when the system boots up causing a warning message to appear when anything attempts to access the boot sector or hard disk partition table No warning message to appear when anything attempts to access the boot sector or hard disk partition table. (Default Value) Disabled · Memory The category is display-only which is determined by POST (Power On Self Test) of the BIOS. Base Memory The POST of the BIOS will determine the amount of base (or conventional) memory installed in the system. The value of the base memory is typically 512 K for systems with 512 K memory installed on the motherboard, or 640 K for systems with 640 K or more memory installed on the motherboard. The BIOS determines how much extended memory is present during the POST. This is the amount of memory located above 1 MB in the CPU's memory address map. Other Memory This refers to the memory located in the 640 K to 1024 K address space. This is memory that can be used for different applications. DOS uses this area to load device drivers to keep as much base memory free for application programs. Most use for this area is Shadow RAM Extended Memory 46 6VM7-4I Motherboard BIOS Features Setup AMIBIOS SETUP ­ BIOS FEATURES CMOS SETUP ( C ) 1999 American Megatrends, Inc. All Rights Reserved 1st Boot Device 2nd Boot Device 3rd Boot Device S. M. A. R. T for Hard Disks BootUp Num-Lock Floppy Drive Seek Password Check Processor Serial Number :Floppy :IDE-0 :CDROM :Disabled :On :Disabled :Setup :Disabled ESC : Quit : Select Item F1 : Help PU/PD/+/- : Modify F5 : Old Values (Shift)F2 :Color F6 : Load BIOS Defaults F7 : Load Setup Defaults Figure 3: BIOS Features Setup · 1st / 2nd / 3rd Boot Device The default value is Floppy or LS-120 / ZIP A: or ATAPI ZIP C: or CDROM or SCSI or NET WORK / I20 or IDE-0~IDE-3 or Disabled. (Default Value) Disabled C2P Concurrency & Master. · DRAM Integrity Mode ECC Disabled For 72 bit ECC type DIMM Modle. (Default Value) · AGP Mode 4X 1X 2X Set AGP Mode is 4X. Set AGP Mode is 2X. · AGP Comp. Driving : 00~FF · AGP Aperture Size 4MB 8MB 16MB 32MB 64MB 128MB 256MB Set AGP Aperture Size to 4MB. (Default Value) Set AGP Aperture Size to 128 MB. Set AGP Aperture Size to 256 MB. · ClKGen Spread Spectrum Disabled Center ± 0. 25% Center ± 0. 5% Spread Spectrum Disabled. 5%(Center Spread). 50 6VM7-4I Motherboard · South Bridge Subsystem ID Disabled Enabled Disable it if you have to install VIA 4 in 1 SP4. 22 or before. (Default Value) Enable south bridge subsystem ID function. · USB Controller All USB Port USB Port 0&1 USB Port 2&3 Disabled Set USB Controller Function used all USB Port. (Default Value) Set USB Controller Function used USB Port 0&1. Set USB Controller Function used USB Port 2&3. USB Controller Function Disabled. · USB Legacy Support Keyboard Keyb+Mouse Disabled Set USB Legacy Support Keyboard. [. . . ] Please search for BIOS unzip file, downloading from internet or any other methods (such as: 6VM7-4I. F1). Complete update process following the instruction. Save BIOS In the very beginning, there is "Save Current BIOS" icon shown in dialog box. It means to save the current BIOS version. [. . . ]