User manual ASUS RS500A-E6PS4

[. . . ] RS500A-E6/PS4 1U Rackmount Server User Guide E6164 Second Edition V2 October 2010 Copyright © 2010 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. ASUS provides this manual "as is" without warranty of any kind, either express or implied, including but not limited to the implied warranties or conditions of merchantability or fitness for a particular purpose. In no event shall ASUS, its directors, officers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of profits, loss of business, loss of use or data, interruption of business and the like), even if ASUS has been advised of the possibility of such damages arising from any defect or error in this manual or product. [. . . ] When you remove any chassis component, the sensor triggers and sends a high-level signal to these leads to record a chassis intrusion event. The default setting is short CASEOPEN and GND pin by jumper cap to disable the function. Locator LED (2-pin LOCATORLED1 and 2-pin LOCATORLED2) These leads are for the locator LED1 and LED2 on the front panel. Connect the Locator LED cables to these 2-pin connector. The LEDs will light up when the Locator button is pressed. Locator Button/Swich (2-pin LOCATORBTN) These leads are for the locator button on the front panel. This button queries the state of the system locator. 4. 5. 4-16 Chapter 4: Motherboard information Chapter 5 ASUS RS500A-E6/PS4 BIOS setup 3- This chapter tells how to change the system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided. 5. 1 Managing and updating your BIOS The following utilities allow you to manage and update the motherboard Basic Input/Output System (BIOS) setup: 1. ASUS EZ Flash 2 (Updates the BIOS using a USB flash disk. ) BUPDATER utility (Updates the BIOS in DOS mode using a bootable USB flash disk drive. ) 3. ASUS CrashFree BIOS 3 (To recover the BIOS using a bootable USB flash disk drive when the BIOS file fails or gets corrupted. ) Save a copy of the original motherboard BIOS file to a bootable USB flash disk drive in case you need to restore the BIOS in the future. Copy the original motherboard BIOS using the ASUS Update or AFUDOS utilities. Refer to the corresponding sections for details on these utilities. 5. 1. 1 ASUS EZ Flash 2 utility The ASUS EZ Flash 2 feature allows you to update the BIOS without having to use a DOS-based utility. Before you start using this utility, download the latest BIOS from the ASUS website at www. asus. com. To update the BIOS using EZ Flash 2 1. Go to the Tools menu to select EZ Flash 2 and press <Enter> to enable it. Or, press <Alt> + <F2> during the POST to enable EZ Flash 2. ASUSTek EZ Flash 2 BIOS ROM Utility V4. 16 Current ROM BOARD: KGNE-D16 VER: 0201 DATE: 04/30/2010 PATH: A:\ A: Update ROM BOARD: KGNE-D16 VER: 0202 DATE: 05/21/2010 Insert the USB flash disk that contains the latest BIOS file to the USB port. Note [Enter] Select or Load [Up/Down/Home/End] Move [Tab] Switch [B] Backup [V] Drive Info [Esc] Exit 5-2 Chapter 5: BIOS setup 3. Press <Tab> to switch between drives until the correct BIOS file is found. When found, EZ Flash 2 performs the BIOS update process and automatically reboots the system when done. · · This function can support devices such as a USB flash disk with FAT 32/16 format and single partition only. DO NOT shut down or reset the system while updating the BIOS to prevent system boot failure! Ensure to load the BIOS default settings to ensure system compatibility and stability. Select the Load Setup Defaults item under the Exit menu. See section 5. 9 Exit Menu for details. 5. 1. 2 BUPDATER utility The succeeding BIOS screens are for reference only. The actual BIOS screen displays may not be the same as shown. The BUPDATER utility allows you to update the BIOS file in DOS environment using a bootable USB flash disk drive with the updated BIOS file. UpdatingtheBIOSfile 1. 3. To update the BIOS file using the BUPDATER utility: Visit the ASUS website at www. asus. com and download the latest BIOS file for the motherboard. Save the BIOS file to a bootable USB flash disk drive. Copy the BUPDATER utility (BUPDATER. exe) from the ASUS support website at support. asus. com to the bootable USB flash disk drive you created earlier. Boot the system in DOS mode, then at the prompt, type: BUPDATER /i[filename]. ROM where [filename] is the latest or the original BIOS file on the bootable USB flash disk drive, then press <Enter>. A:\>BUPDATER /i[file name]. ROM ASUS RS500A-E6/PS4 5-3 4. The utility verifies the file, then starts updating the BIOS file. ASUSTek BIOS Update for DOS V1. 06 (09/08/04) FLASH TYPE: MXIC 25L1605A Current ROM BOARD: KGNE-D16 VER: 0201 DATE: 04/30/2010 PATH: WARNING!Do not turn off power during flash BIOS Update ROM BOARD: KGNE-D16 VER: 0202 DATE: 05/21/2010 Note Writing BIOS: DO NOT shut down or reset the system while updating the BIOS to prevent system boot failure! 5. The utility returns to the DOS prompt after the BIOS update process is completed. Reboot the system from the hard disk drive. The BIOS update is finished! [. . . ] Use the arrow keys to select Installation from the Boot Options menu. Boot from Hard Disk Installation Repair Installed System Rescue System Check Installation Media Firmware Test Memory Test Boot Options | F1 Help F2 Language F3 Video Mode English(US) 1024 X768 F4 Source DVD F5 Kernel F6 Driver Default No 3. Press <F6>, then select Yes from the menu. Press <Enter>. Boot from Hard Disk Installation Repair Installed System Rescue System Check Installation Media Firmware Test Memory Test Yes No File URL F5 Kernel F6 Driver Default No Boot Options | F1 Help F2 Language F3 Video Mode English(US) 1024 X768 F4 Source DVD ASUS RS500A-E6/PS4 7-11 4. Insert the RAID driver disk to the floppy disk drive. Type the command acpi=off apic=bigsmp brokenmodules=ahci in Boot Options field, and press <Enter>. Boot from Hard Disk Installation Repair Installed System Rescue System Check Installation Media Firmware Test Memory Test Boot Options acpi=off apic=bigsmp brokenmodules=ahci F1 Help F2 Language F3 Video Mode English(US) 1024 X768 F4 Source DVD F5 Kernel F6 Driver Default Yes 5. When below screen appears, select the USB floppy disk drive (sda) as the driver update medium. Select OK, then press <Enter>. Please choose the Driver Update medium. [. . . ]