User manual ASUS SILENT SQUARE PRO

[. . . ] IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe. ii Contents Safety information. [. . . ] (Self-Monitoring, Analysis and Reporting Technology) is a monitor system. When read/write of your hard disk errors occur, this feature allows the hard disk to report warning messages during POST. Configuration options: [Enabled] [Disabled] Staggered Spin-up [Disabled] Staggered spin-up is a feature defined in the Serial ATA Specifications. It enables an HBA to individually spin-up attached SATA devices to avoid maximum current charged by applying all attached SATA devices at the same time. Configuration options: [Disabled] [Enabled] Chapter 5 5-22 Chapter 5: BIOS setup 5. 4. 5 PCH SCU Configuration Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc. Advanced Patsburg B/D sku only Device1 Intel ISR10a Device2 Intel ISR10a Device3 Intel ISR10a Device4 Intel ISR10a Device5 Intel ISR10a Device6 Intel ISR10a Device7 Intel ISR10a Device8 Intel ISR10a Sata only RAID5 [Disabled] Sata only RAID5 →←: Select Screen ↑↓: Select Item Enter: Select Item +/-: Change Opt. F1: General Help F2: Previous Values F5: Optimized Defaults F10: Save & Exit ESC: Exit Version 2. 15. 1219. Copyright (C) 2011 American Megatrends, Inc. 5. 4. 6 PCI Subsystem Settings Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc. Advanced V 2. 05. 00 In case of multiple Option ROMs (Legacy and EFI Compatible), specifies what PCI option ROM to lanuch. PCI Bus Driver Version PCI Option ROM Handling PCI ROM Priority [EFI Compatible ROM] PCI 64bit Resources Handling Above 4G Decoding [Disabled] PCI Common Setting PCI Latency Timer VGA Palette Snoop PERR# Generation SERR# Generation Load RT32 Image [32 PCI Bus Clocks] [Disabled] [Disabled] [Disabled] [Enabled] →←: Select Screen ↑↓: Select Item Enter: Select Item +/-: Change Opt. F1: General Help F2: Previous Values F5: Optimized Defaults F10: Save & Exit ESC: Exit PCI Express Settings PCIE Slot Option Rom Configuration Version 2. 15. 1219. Copyright (C) 2011 American Megatrends, Inc. PCI ROM Priority [EFI Compatible ROM] In case of multiple option roms (Legacy and EFI Compatible), specifies what PCI option rom to launch. Configuration options: [Legacy ROM] [EFI Compatible ROM] SILENT SQUARE PRO 5-23 Chapter 5 PCI Latency Timer [32 PCI Bus Clocks] Value to be programmed into PCI latency timer register. Configuration options: [32 PCI Bus Clocks] [64 PCI Bus Clocks] [96 PCI Bus Clocks] [128 PCI Bus Clocks] [160 PCI Bus Clocks] [192 PCI Bus Clocks] [224 PCI Bus Clocks] [248 PCI Bus Clocks] VGA Palette Snoop [Disabled] Allows you to enable/disable the VGA pallette registers snooping. F1: General Help F2: Previous Values F5: Optimized Defaults F10: Save & Exit ESC: Exit Version 2. 15. 1219. Copyright (C) 2011 American Megatrends, Inc. Chapter 5 5-28 Chapter 5: BIOS setup 5. 4. 9 USB Configuration Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc. Auto option disables legacy support if no USB devices are connected. DISABLE option will keep USB devices available only for EFI applications. USB Configuration USB Devices: 3Drivers, 1Keyboard, 1 Mouse, 3 Hubs Legacy USB Support EHCI Hand-off USB hardware delays and time-outs USB transfer time-out Device reset time-out [Enabled] [Disabled] →←: Select Screen ↑↓: Select Item Enter: Select Item +/-: Change Opt. F1: General Help F2: Previous Values F5: Optimized Defaults F10: Save & Exit ESC: Exit [20 sec] [20 sec] USB Ports Configuration Version 2. 15. 1219. Copyright (C) 2011 American Megatrends, Inc. Legacy USB Support [Enabled] Allows you to enable or disable Legacy USB device support. Configuration options: [Enabled] [Disabled] [Auto] EHCI Hand-off [Disabled] This is a workaround for 0ses without EHCI. Ownership change should be claimed by EHCI driver. Configuration options: [Disabled] [Enabled] USB hardware delays and time-outs USB transfer time-out [20 sec] The time-out value for control, bulk, and interrupt transfer. Configuration options: [1 sec] [5 sec] [10 sec] [20 sec] Device reset time-out [20 sec] USB mass storage device start unit command time-out. Configuration options: [10 sec] [20 sec] [30 sec] [40 sec] SILENT SQUARE PRO 5-29 Chapter 5 USB Ports Configuration Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc. Advanced Enable/disable USB 2. 0 (EHCI) Support. →←: Select Screen ↑↓: Select Item Enter: Select Item +/-: Change Opt. [. . . ] Double-click the ASSETUP. EXE to run the support DVD. 3. Click the Intel® Rapid Storage Technology enterprise 3. 0. Chapter 7 7-26 Chapter 7: Driver installation 4. When the Welcome to the Setup Program appears, click Next. 5. Read the Warning message and click Next to continue. 6. Read the License Agreement and click Yes to continue. SILENT SQUARE PRO 7-27 Chapter 7 7. Read the Readme File Information and click Next to continue. 8. After completing the installation, click Next to complete the setup process. 9. Select Yes, I want to restart my computer now and click Finish to restart your computer before using the program. Chapter 7 7-28 Chapter 7: Driver installation 7. 8 This section provides the instructions on how to install Intel® I350 Gigabit Adapters Driver. To install the Intel® I350 Gigabit Adapters Driver on a Windows® OS: 1. 2. Restart the computer, and then log on with Administrator privileges. Insert the motherboard/system support DVD to the optical drive. The DVD automatically displays the Drivers menu if Autorun is enabled in your computer. If Autorun is NOT enabled in your computer, browse the contents of the support DVD to locate the file AUTORUN. EXE and double-click the AUTORUN. EXE and follow step 4 to run the installation. Intel® I350 Gigabit Adapters Driver installation 3. Click Intel® I350-AM4 Gigabit Adapters Driver. SILENT SQUARE PRO 7-29 Chapter 7 4. When the Intel® PRO Network Connections – InstallShield Wizard window appears, click Next. 5. Click I accept the terms in the license agreement and then click Next to continue. Chapter 7 7-30 Chapter 7: Driver installation 6. Select the programs you want to install and click Next to continue. 7. Click Install. SILENT SQUARE PRO 7-31 Chapter 7 8. Wait for the installation process to complete. . 9. Click Finish to finish the installation. Chapter 7 7-32 Chapter 7: Driver installation 7. 9 The support DVD that came with the motherboard package contains the drivers, management applications, and utilities that you can install to avail all motherboard features. The contents of the support DVD are subject to change at any time without notice. [. . . ]