User manual ASUS V2-P5945G

[. . . ] V-Series P5945G ASUS PC (Desktop Barebone) Installation Manual R E2873 First Edition V1 September 2006 Copyright © 2006 ASUSTeK COMPUTER INC. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. ASUS PROVIDES THIS MANUAL "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. [. . . ] The USBPW56 jumper is for the internal USB connectors (USB port 5-8) that you can connect to additional USB ports. USBPW12 23 R P5L-VM 1394 12 R +5V (Default) +5VSB USBPW56 12 23 P5L-VM 1394 USB Device Wake Up · +5V (Default) +5VSB The USB device wake-up feature requires a power supply that can provide 500 mA on the +5VSB lead for each USB port; otherwise, the system would not power up. The total current consumed must NOT exceed the power supply capability (+5VSB) whether under normal condition or in sleep mode. · 4-4 Chapter 4: Motherboard info 4. 3 1. Jumpers Floppy disk drive connector (34-1 pin FLOPPY) This connector is for the provided floppy disk drive (FDD) signal cable. Insert one end of the cable to this connector, then connect the other end to the signal connector at the back of the floppy disk drive. Pin 5 on the connector is removed to prevent incorrect cable connection when using an FDD cable with a covered Pin 5. FLOPPY P5L-VM 1394 R NOTE: Orient the red markings on the floppy ribbon cable to PIN 1. P5L-VM 1394 Floppy Disk Drive Connector ASUS V-Series P5945G PIN 1 4-5 2. IDE connectors (40-1 pin PRI_IDE) The onboard IDE connectors are for Ultra DMA 100/66/33 signal cables. There are three connectors on each Ultra DMA 100/66/33 signal cable: blue, black, and gray. Connect the blue connector to the motherboard's IDE connector, then select one of the following modes to configure your device(s). PRI_IDE P5L-VM 1394 R P5L-VM 1394 IDE Connector NOTE: Orient the red markings (usually zigzag) on the ID ribbon cable to PIN 1. Drive jumper setting Single device Two devices Cable-Select or Master Cable-Select Master Slave Mode of device(s) Master Slave Master Slave PIN1 Cable connector Black Black Gray Black or gray · Pin 20 on the IDE connector is removed to match the covered hole on the Ultra DMA cable connector. This prevents incorrect insertion when you connect the IDE cable. Use the 80-conductor IDE cable for Ultra DMA 100/66/33 IDE devices. · If any device jumper is set as "Cable-Select, " make sure all other device jumpers have the same setting. 4-6 Chapter 4: Motherboard info 3. Serial ATA connectors (7-pin SATA1, SATA2, SATA3, SATA4) These connectors are for the Serial ATA signal cables for Serial ATA hard disk drives. SATA3 P5L-VM 1394 R SATA4 GND RSATA_RXN4 RSATA_RXP4 GND RSATA_TXN4 RSATA_TXP4 GND GND RSATA_TXP3 RSATA_TXN3 GND RSATA_RXP3 RSATA_RXN3 GND SATA1 GND RSATA_RXN1 RSATA_RXP1 GND RSATA_TXN1 RSATA_TXP1 GND SATA2 GND RSATA_RXN2 RSATA_RXP2 GND RSATA_TXN2 RSATA_TXP2 GND P5L-VM 1394 SATA Connectors When using the connectors in Standard IDE mode, connect the primary (boot) hard disk drive to the SATA1/2 connector. Refer to the table below for the recommended SATA hard disk drive connections. Serial ATA hard disk drive connection Connector Color Setting Use SATA1/2 SATA3/4 Red Black Master Slave Boot disk Data Disk right angle side Connect the right-angle side of SATA signal cable to SATA device. Or you may connect the right-angle side of SATA cable to the onboard SATA port to avoid mechanical conflict with a long card in PCI2 slot. ASUS V-Series P5945G 4-7 4. CPU, Power and Chassis fan connectors (4-pin CPU_FAN, 3-pin CHA_FAN) The fan connectors support cooling fans of a total of 1A~2. 2A (26. 4W max. ) at +12V. Connect the fan cables to the fan connectors on the motherboard, making sure that the black wire of each cable matches the ground pin of the connector. Do not forget to connect the fan cables to the fan connectors. Insufficient air flow inside the system may damage the motherboard components. DO NOT place jumper caps on the fan connectors. CPU_FAN CHA_FAN Rotation +12V GND P5L-VM 1394 Fan Connectors 5. Digital Audio connector (4-1 pin SPDIF_OUT) This connector is for the S/PDIF audio module to allow digital sound output. Connect one end of the S/PDIF audio cable to this connector and the other end to the S/PDIF module. P5L-VM 1394 R P5L-VM 1394 CPU FAN PWM CPU FAN IN CPU FAN PWR GND R SPDIF_OUT P5L-VM 1394 Digital Audio Connector The S/PDIF out module is purchased separately. 4-8 +5V Chapter 4: Motherboard info SPDIFOUT GND 6. IEEE 1394a port connector (10-1 pin IE1394_2) This connector is for a IEEE 1394a port. Connect the IEEE 1394a module cable to this connector, then install the module to a slot opening at the back of the system chassis. P5L-VM 1394 R +12V TPB1+ GND TPA1+ IE1394_2 P5L-VM 1394 IEEE 1394a Connector GND +12V TPB1GND TPA1- 1 Never connect a USB cable to the IEEE1394a connector. The IEEE 1394 module is purchased separately. 7. Serial port connector (10-1 pin COM1) This connector is for a serial (COM) port. Connect the serial port module cable to this connector, then install the module to a slot opening at the back of the system chassis. P5L-VM 1394 R COM1 PIN 1 P5L-VM 1394 COM Port Connector The COM module is purchased separately. ASUS V-Series P5945G 4-9 8. ATX power connectors (24-pin EATXPWR and 4-pin ATX12V) These connectors are for ATX power supply plugs. The power supply plugs are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit. · · Do not forget to connect the 4-pin ATX +12 V power plug; otherwise, the system will not boot. Use of a PSU with a higher power output is recommended when configuring a system with more power-consuming devices. The system may become unstable or may not boot up if the power is inadequate. Make sure that your power supply unit (PSU) can provide at least the minimum power required by your system. [. . . ] When you press <Enter>, a confirmation message appears. Use the left/right arrow key to select between [Yes] or [No], then press <Enter> to confirm your choice. Please see page 2-3, section 2. 1. 2 for details. ASUSTek EZ Flash 2 BIOS ROM Utility V3. 00 FLASH TYPE: SST 25VF040/B Current ROM BOARD: P5L-VM-1394 VER: 0106 DATE: 07/26/06 PATH: A:\ A: Update ROM BOARD: Unknown VER: Unknown DATE: Unknown Note [Enter] Select or Load [Tab] Switch [B] Backup [ESC] Exit [Up/Down/Home/End] Move 5-36 Chapter 5: BIOS setup 5. 7. 2 ASUS O. C. Profile BIOS SETUP UTILITY Tools This item allows you to store or load multiple BIOS settings. O. C. [. . . ]