User manual ASUS V2-P5V900 V SERIES P5V900 USER’S MANUAL(ENGLISH)

[. . . ] IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. ii Table of contents Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 3. Click the Utilities tab, then click ASUS PC Probe II. Follow the screen instructions to complete installation. Launching PC Probe II You can launch the PC Probe II right after installation or anytime from the Windows® desktop. To launch the PC Probe II from the Windows® desktop, click Start > All Programs > ASUS > PC Probe II. After launching the application, the PC Probe II icon appears in the Windows® taskbar. Click this icon to close or restore the application. Using PC Probe II Main window The PC Probe II main window allows you to view the current status of your system and change the utility configuration. By default, the main window displays the Preference section. You can close or restore the Preference section by clicking on the triangle on the main window right handle. Click to close the Preference panel 3-6 Chapter 3: Starting up Button Function Opens the Configuration window Opens the Report window Opens the Desktop Management Interface window Opens the Peripheral Component Interconnect window Opens the Windows Management Instrumentation window Opens the hard disk drive, memory, CPU usage window Shows/Hides the Preference section Minimizes the application Closes the application Sensor alert When a system sensor detects a problem, the main window right handle turns red, as the illustrations below show. When displayed, the monitor panel for that sensor also turns red. Refer to the Monitor panels section for details. Preferences You can customize the application using the Preference section in the main window. Click the box before each preference to activate or deactivate. ASUS Vintage V2-P5V900 3-7 Hardware monitor panels The hardware monitor panels display the current value of a system sensor such as fan rotation, CPU temperature, and voltages. The hardware monitor panels come in two display modes: hexagonal (large) and rectangular (small). When you check the Enable Monitoring Panel option from the Preference section, the monitor panels appear on your computer's desktop. Small display Large display Changing the monitor panels position To change the position of the monitor panels on the desktop, click the arrow down button of the Scheme options, then select another position from the list box. This chapter includes the motherboard layout, jumper settings, and connector locations. Motherboard introduction Chapter 4 4. 1 Introduction The Vintage V2-P5V900 barebone system comes with an ASUS motherboard. This chapter provides technical information about the motherboard for future upgrades or system reconfiguration. 4. 2 Motherboard layout 21. 8cm (8. 6in) ESATA PARALLEL PORT USB12 ATX12V USBPW56 USBPW78 Top:Line In Center:Line Out Below:Mic In SATA_A R JMB363 PCIEX1 RTL8201CL CR2032 3V Lithium Cell CMOS Power CD AUX PCI1 PCI2 VIA 8237A CHA_FAN 4Mb BIOS SATA2 SATA1 ADI1986A SPDIF_OUT USBPW56 USBPW78 USB56 USB78 SB_PWR CLRTC CHASSIS AAFP COM2 F_PANEL 4-2 Chapter 4: Motherboard info SEC_IDE PCIEX16 BUZZER PRI_IDE 24. 5cm (9. 6in) VIA P4M890 EATXPWR Bottom: USB3 USB4 Top: RJ-45 FLOPPY VGA DDR2 DIMM1 (128 bit, 240-pin module) DDR2 DIMM2 (128 bit, 240-pin module) LGA775 CPU_FAN Super I/O PS/2KBMS T: Mouse B: Keyboard KBPWR 4. 3 1. Jumpers Clear RTC RAM (CLRTC) This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in the CMOS, which includes the system setup information such as system passwords. Turn OFF the computer and unplug the power cord. Move the jumper cap from pins 1-2 (default) to pins 2-3. Keep the cap on pins 2-3 for about 5-10 seconds, then move the cap back to pins 1-2. Plug the power cord and turn ON the computer. Hold down the <Del> key during the boot process and enter BIOS setup to re-enter data. R CLRTC 12 Normal (Default) 23 Clear CMOS Clear RTC RAM Except when clearing the RTC RAM, never remove the cap on CLRTC jumper default position. Removing the cap will cause system boot failure. ASUS Vintage V2-P5V900 4-3 2. USB device wake-up (3-pin USBPW12, USBPW34, USBPW56, USBPW78) Set these jumpers to +5V to wake up the computer from S1 sleep mode (CPU stopped, DRAM refreshed, system running in low power mode) using the connected USB devices. Set to +5VSB to wake up from S3 and S4 sleep modes (no power to CPU, DRAM in slow refresh, power supply in reduced power mode). [. . . ] Configuration options: [Disabled] [Enabled] Halt On [All, But Keyboard] Allows you to error report type. Configuration options: [All Errors] [No Errors] [All, But Keyboard] [All, But Diskette] [All, But Disk/Key] 5. 6. 3 Security Phoenix-Award BIOS CMOS Setup Utility Boot Security Select Menu Clear Clear [Setup] Item Specific Help Supervisor Password User Password Password Check Supervisor Password User Password These fields allow you to set passwords: To set a password: 1. Select an item then press <Enter>. Type in a password using a combination of a maximum of eight (8) alpha-numeric characters, then press <Enter>. [. . . ]