User manual ASUS V3-M2NC61P

[. . . ] Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. The product name and revision number are both printed on the product itself. Manual revisions are released for each product design represented by the digit before and after the period of the manual revision number. Manual updates are represented by the third digit in the manual revision number. [. . . ] The LED blinks when there is data received. The system message LED feature requires an ACPI OS and driver support. System Management Interrupt Connector (2-pin SMI) This 2-pin connector allows you to manually place the system into a suspend mode, or "Green" mode, where system activity is instantly decreased to save power and to expand the life of certain system components. Attach the case-mounted suspend switch this 2-pin connector. ATX Power Switch / Soft-Off Switch Connector (2-pin PWR. SW) The system power is controlled by a momentary switch attached to this connector. Pressing the button switches the system between ON and SLEEP, or ON and SOFT OFF, depending on the BIOS or OS settings. Pressing the button while in the ON mode for more than 4 seconds turns the system off. Reset Switch Connector (2-pin RESET) This 2-pin connector connects to the case-mounted reset switch for rebooting the system without turning off the power switch. ASUS Terminator Barebone System 59 NOTES 60 Chapter 3: Motherboard Information Chapter 4 This chapter describes the power-up sequence and gives information on the BIOS beep codes. The contents of the support CD that comes with the Terminator Barebone System package are also enumerated. ASUS Terminator Barebone System Starting Up 61 4. 1 Powering Up the First Time 1. After making all the connections, replace the system case cover. Be sure that all switches are off (in some systems, marked with ). The support installation menu should appear. If the menu does not appear, double-click or run D:\ASSETUP. EXE (assuming that your CD-ROM drive is drive D). NOTE The support CD contents are subject to change at any time without notice. 64 Chapter 4: Starting Up 4. 2. 3 · · · · · · · Applications Display Driver: This driver will automatically detect and install the SiS Display Drivers. SiS AGP Driver: Installs the SiS 2D/3D AGP video driver to support high-performance graphical applications. SiS 7018 PCI Audio Driver: Installs the SiS 7018 PCI audio drivers to activate the AC `97 compliant audio features. LAN Driver: Installs the driver for the onboard LAN controller. SiS IDE Utility: Installs the SiS IDE Utility for the two IDE channels. ASUS PC Probe Vx. xx. xx: Installs a smart utility that can monitor the computer fan, temperature, and voltages. Install ASUS Update Vx. xx. xx : Installs the ASUS Update program. This program allows you download the latest version of Flash BIOS from the ASUS website. Before using ASUS Update, you should install a network card and a TCP/IP network driver. Microsoft DirectX 8. 0a Driver: Installs the Microsoft Direct Driver. · ASUS Terminator Barebone System 65 · · PC-Cillin 2000 V7. 51: Installs the PC-cillin virus protection software. [. . . ] ATAPI CD-ROM This field allows you to select which ATAPI CD-ROM drive to use in the boot sequence. Pressing [Enter] will show the product IDs of all your connected ATAPI CD-ROM drives. IMPORTANT Make sure the ATAPI CD-ROM drive that you want to use in the boot sequence is connected to either the PRIMARY or SECONDARY IDE connectors, not to the ATA100 connectors. Currently, the Promise® Ultra DMA/100 chip does not support this feature. 102 Chapter 5: BIOS Information Other Boot Device Select [INT18 Device (Network)] Configuration options: [Disabled] [SCSI/Onboard ATA Boot Device] [INT18 Device (Network)] Plug & Play O/S [No] This field allows you to use a Plug-and-Play (PnP) operating system to configure the PCI bus slots instead of using the BIOS. When [Yes] is selected, interrupts may be reassigned by the OS. [. . . ]