User manual ASUS V3-P5G31

[. . . ] IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. ii Table of contents Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Shift the gear to the performance setting that you like. ASUS V-Series P5G965 3-9 Maximum Performance Medium Performance High Performance Maximum Power Saving 3. 4. 3 ASUS AI Nap This feature allows you to minimize the power consumption of your computer whenever you are away. Enable this feature for minimum power consumption and a more quiet system operation. Click Yes on the confirmation screen. To exit AI Nap mode, press the system power or mouse button then click Yes on the confirmation screen. 3-10 Chapter 3: Starting up This chapter gives information about the motherboard that comes with the system. This chapter includes the motherboard layout, jumper settings, and connector locations. Motherboard information Chapter 4 4. 1 Introduction The V-Series P5G965 barebone system comes with an ASUS motherboard. This chapter provides technical information about the motherboard for future upgrades or system reconfiguration. 4. 2 Motherboard layout 24. 5cm (9. 6in) PS/2KBMS T Mouse : B: Keyboard KBPWR CHA_FAN1 CPU_FAN Super I/O ESATA DDR2 DIMM_A1 (64 bit, 240-pin module) DDR2 DIMM_A2 (64 bit, 240-pin module) DDR2 DIMM_B1 (64 bit, 240-pin module) VGA 1394_USB12 ATX12V R DDR2 DIMM_B2 (64 bit, 240-pin module) LGA775 PARALLE PORT P5B-VM Intel G965MCH RTL8111B AUDIO SATA_RAID1 JMicron JMB363 PCIEX16 PCI1 SB_PWR COM1 TSB43AB22A PCI2 PCIEX4_1 IE1394_2 ADH AAFP Intel ICH8 CR2032 3V Lithium Cell CMOS Power 8Mb BIOS FLOPPY LAN_USB34 SATA1 SATA2 AD1988 CD SATA3 PRI_EIDE USB56 USB78 SATA4 PANEL CHASSIS USB910 CLRTC 4-2 Chapter 4: Motherboard info 24. 5cm (9. 6in) EATXPWR 4. 3 1. Jumpers Clear RTC RAM (CLRTC) This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in CMOS, which include system setup information such as system passwords. Turn OFF the computer and unplug the power cord. Move the jumper cap from pins 1-2 (default) to pins 2-3. Keep the cap on pins 2-3 for about 5-10 seconds, then move the cap back to pins 1-2. Plug the power cord and turn ON the computer. The power supply plugs are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit. EATX12V GND +12V DC P5B-VM GND +12V DC EATXPWR +3 Volts +12 Volts +12 Volts +5V Standby Power OK Ground +5 Volts Ground +5 Volts Ground +3 Volts +3 Volts Ground +5 Volts +5 Volts +5 Volts -5 Volts Ground Ground Ground PSON# Ground -12 Volts +3 Volts ATXPowerConnector · For a fully configured system, we recommend that you use a power supply unit (PSU) that complies with ATX 12 V Specification 2. 0 (or later version) and provides a minimum power of 400 W. Do not forget to connect the 4-pin EATX12V power plug; otherwise, the system will not boot. Use of a PSU with a higher power output is recommended when configuring a system with more power-consuming devices. The system may become unstable or may not boot up if the power is inadequate. · · 7. Optical drive audio connector (4-pin CD) These connectors allow you to receive stereo audio input from sound sources such as a CD-ROM, TV tuner, or MPEG card. R P5B-VM R InternalAudioConnector CD (black) Right Audio Channel Ground Ground Left Audio Channel ASUS V-Series P5G965 4-9 8. Front panel audio connector (10-1 pin AAFP) This connector is for a chassis-mounted front panel audio I/O module that supports either HD Audio or legacy AC`97 audio standard. Connect one end of the front panel audio I/O module cable to this connector. P5B-VM Azalia-compliant pin definition HP_HD Legacy AC'97-compliant pin definition NC NC NC AGND Line out_L NC Line out_R MIC2_R MIC2_L R AAFP MIC2_JD PRESENSE# AGND HP_L Jack_Sense HP_R MIC2_R MIC2_L FrontPanelAudioConnector · We recommend that you connect a high-definition front panel audio module to this connector to avail of the motherboard's highdefinition audio capability. By default, this connector is set to HD Audio. If you want to connect a AC' 97 front panel audio module to this connector, set the Front Panel Support Type item in the BIOS setup to [AC97]. 5 Onboard Device Configuration for details. · 4-10 Chapter 4: Motherboard info 9. Chassis intrusion connector (4-1 pin CHASSIS) This connector is for a chassis-mounted intrusion detection sensor or switch. Connect one end of the chassis intrusion sensor or switch cable to this connector. The chassis intrusion sensor or switch sends a high-level signal to this connector when a chassis component is removed or replaced. [. . . ] To clear the supervisor password, select the Change Supervisor Password then press <Enter>. The message "Password Uninstalled" appears. If you forget your BIOS password, you can clear clear it by erasing the CMOS Real Time Clock (RTC) RAM. See section "4. 3 Jumpers" for information on how to erase the RTC RAM. 5-32 Chapter 5: BIOS setup After you have set a supervisor password, the other items appear to allow you to change other security settings. Security Settings Supervisor Password User Password : Not Installed : Not Installed [Full Access] [Setup] Change Supervisor Password User Access Level Change User Password Clear User Password Password Check User Access Level [Full Access] This item allows you to select the access restriction to the Setup items. Configuration options: [No Access] [View Only] [Limited] [Full Access] No Access prevents user access to the Setup utility. [. . . ]