User manual ASUS V3-P5G33

[. . . ] IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. ii Table of contents Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Turn OFF the computer and unplug the power cord. Move the jumper cap from pins 1-2 (default) to pins 2-3. Keep the cap on pins 2-3 for about 5~10 seconds, then move the cap back to pins 1-2. Plug the power cord and turn ON the computer. Hold down the <Del> key during the boot process and enter BIOS setup to re-enter data. Except when clearing the RTC RAM, never remove the cap on CLRTC jumper default position. Removing the cap will cause system boot failure! P5L-VM 1394 R CLRTC 12 Normal (Default) 23 Clear CMOS P5L-VM 1394 Clear RTC RAM You do not need to clear the RTC when the system hangs due to overclocking. For system failure due to overclocking, use the C. P. R. Shut down and reboot the system so the BIOS can automatically reset parameter settings to default values. ASUS V-Series P5945G 4-3 2. Keyboard power (3-pin KBPWR) This jumper allows you to enable or disable the keyboard wake-up feature. Set this jumper to pins 2-3 (+5VSB) to wake up the computer when you press a key on the keyboard (the default is the Space Bar). This feature requires an ATX power supply that can supply at least 1A on the +5VSB lead, and a corresponding setting in the BIOS. KBPWR P5L-VM 1394 2 1 +5V (Default) 3 2 +5VSB P5L-VM 1394 Keyboard Power Setting 3. USB device wake-up (3-pin USBPW12, USBPW56) Set these jumpers to +5V to wake up the computer from S1 sleep mode (CPU stopped, DRAM refreshed, system running in low power mode) using the connected USB devices. Set to +5VSB to wake up from S3 and S4 sleep modes (no power to CPU, DRAM in slow refresh, power supply in reduced power mode). Make sure that your power supply unit (PSU) can provide at least the minimum power required by your system. If you intent to use a PSU with 20-pin and 4-pin power plugs, make sure that the 20-pin power plug can provide at least 15A on +12V and that the PSU has a minimum power rating of 350 W. The system may become unstable or may not boot up if the power is inadequate. The ATX 12 V Specification 2. 0-compliant PSU passed the motherboard power requirement test with the following configuration: CPU : Memory : Graphics card : Parallel ATA devices : Serial ATA device : Optical drive : SCSI devices : · Intel® Pentium® 4 3. 6 GHz 512 MB DDR (x 4) PCI Express x16 Nvidia EN5900 IDE hard disk drive (x 2) SATA hard disk drive CD-ROM (x2) SCSI card and SCSI hard disk drive · · · You must install a PSU with a higher power rating if you intend to install additional devices. EATX12V GND +12V DC P5L-VM 1394 EATXPWR +3 Volts +12 Volts +12 Volts +5V Standby Power OK Ground +5 Volts Ground +5 Volts Ground +3 Volts +3 Volts Ground +5 Volts +5 Volts +5 Volts -5 Volts Ground Ground Ground PSON# Ground -12 Volts +3 Volts R P5L-VM 1394 ATX Power Connector 4-10 GND +12V DC Chapter 4: Motherboard info 9. Optical drive audio connector (4-pin CD) This connector is for the 4-pin audio cable that connects to the audio connector at the back of the optical drive. CD (black) P5L-VM 1394 Internal Audio Connector Enable the CD-IN function in the audio utility when using this connector. 10. USB connectors (10-1 pin USB56, USB78) These connectors are for USB 2. 0 ports. Connect the USB module cable to any of these connectors, then install the module to a slot opening at the back of the system chassis. These USB connectors comply with USB 2. 0 specification that supports up to 480 Mbps connection speed. P5L-VM 1394 R USB+5V USB_P8USB_P8+ GND NC Right Audio Channel Ground Ground Left Audio Channel P5L-VM 1394 R USB78 USB56 1 USB+5V USB_P7USB_P7+ GND 1 USB+5V USB_P5USB_P5+ GND P5L-VM 1394 USB 2. 0 Connectors Never connect a 1394 cable to the USB connectors. The USB module is purchased separately. ASUS V-Series P5945G USB+5V USB_P6USB_P6+ GND NC 4-11 11. Front panel audio connector (10-1 pin AAFP) This connector is for a chassis-mounted front panel audio I/O module that supports either HD Audio or legacy AC'97 audio standard. AAFP HD-audio-compliant pin definition GND PRESENSE# SENSE1_RETUR SENSE2_RETUR P5L-VM 1394 R Legacy AC'97 compliant definition AGND NC NC PORT1L PORT1R PORT2R SEBSE_SEND PORT2L P5L-VM 1394 Front Panel Audio Connector · We recommend that you connect a high-definition front panel audio module to this connector to avail of the motherboard's highdefinition audio capability. By default, this connector is set to AC97 Audio. [. . . ] Confirm the password when prompted. The message "Password Installed" appears after you set your password successfully. To change the user password, follow the same steps as in setting a user password. Clear User Password Select this item to clear the user password. ASUS V-Series P5945G 5-35 Password Check [Setup] When set to [Setup], BIOS checks for user password when accessing the Setup utility. When set to [Always], BIOS checks for user password both when accessing Setup and booting the system. Configuration options: [Setup] [Always] 5. 7 Tools menu ASUS EZ Flash 2 ASUS O. C. Profile 5. 7. 1 ASUS EZ Flash 2 Allows you to run ASUS EZ Flash 2. [. . . ]