User manual ASUS VE258Q

[. . . ] Operation is subject to the following two conditions: (1) ENGLISH This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for Class B Personal Computers and peripherals, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the device is operated in a residential environment. This device generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] Thinner Spray-type cleaner Benzine Wax Abrasive cleaner Acid or Alkaline solvent Touching the cabinet and the LCD screen with any product made from rubber or plastic for a long time may cause degeneration or loss of paint on the cabinet and the LCD screen. Stains can be removed with a cloth lightly moistened with a mild detergent solvent. Then wipe the cabinet with a soft dry cloth. Periodic cleaning with a soft dry cloth is recommended. because these will damage the LCD screen. Stains can be removed with a cloth lightly moistened with a mild detergent solvent. Then wipe the touch screen with a soft dry cloth. Don't pour the detergent solvent on the touch screen. CABINET LCD SCREEN 3 FOR YOUR SAFETY BEFORE YOU OPERATE THE MONITOR FEATURES ProLite VE258Q : 38cm (15. 0") TFT Color LCD Monitor Resistive Film ENGLISH 4 ProLite T1730SR : 43cm (17. 0") TFT Color LCD Monitor Resistive Film ProLite T1930SR : 48cm (19. 0") TFT Color LCD Monitor Resistive Film ProLite VE258Q: Supports Resolutions up to 1024 × 768 ProLite T1730SR / ProLite T1930SR : Supports Resolutions up to 1280 × 1024 Digital Character Smoothing Automatic Set-up Plug & Play VESA DDC2B Compliant Windows® 95/98/2000/Me/XP/Vista Compliant Power Management (VESA DPMS Compliant) ProLite VE258Q : VESA Standard (75mm×75mm) for Arm or Wall Mounting ProLite T1730SR / ProLite T1930SR : VESA Standard (100mm×100mm) for Arm or Wall Mounting Stereo Speakers SPECIAL NOTES ON TOUCH PANEL Permanent damage can occur if Sharp Edged, Pointed or Metal items are used to activate Touch. This could invalidate any remaining warranty. We recommend to use a plastic stylus (tip R0. 8 or over) or finger. BEFORE YOU OPERATE THE MONITOR CHECKING THE CONTENTS OF THE PACKAGE The following accessories are included in your package. Check to see if they are enclosed with the monitor. For further information, please contact your computer dealer first for advice. Procedure for turning ON the Power Switch Turn ON the monitor first, and then the computer. Touch screen driver software Touch screen driver software and system may not start when you start your computer while touching the screen. Touch screen driver software may not run due to the power saving function depending on the BIOS of your computer. In this case, set the power saving function to off. ADJUSTING THE VIEWING ANGLE For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor's angle to your own preference. Hold the panel so that the monitor does not topple when you change the monitor's angle. You are able to adjust the monitor's angle up to 90 degrees upward, 5 degrees downward. NOTE Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen. Careful attention is required not to catch your fingers or hands when you change the angle. 5° 90° BEFORE YOU OPERATE THE MONITOR 8 ENGLISH OPERATING THE MONITOR To create the best picture, your iiyama LCD monitor has been preset at the factory with the COMPLIANT TIMING shown on page 21. You are also able to adjust the picture by following the button operation shown below. [. . . ] It is possible that the video signal from the computer may be on while the H or V sync signal is missing. In this instance, the POWER MANAGEMENT feature may not work properly. The monitor may not be restored from the power management depending on your computer system even if the screen is touched again. In this case, set the power management feature to off. 15 OPERATING THE MONITOR TROUBLE SHOOTING If the monitor fails to operate correctly, please follow the steps below for a possible solution. [. . . ]