User manual ASUS VS228N

[. . . ] IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. ii Contents Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Connect the fan cables to the fan connectors on the motherboard, making sure that the black wire of each cable matches the ground pin of the connector. Do not forget to connect the fan cables to the fan connectors. Insufficient air flow inside the system may damage the motherboard components. Do not place jumper caps on the fan connectors! CPU_FAN1 CPU_FAN1 GND FANPWR2 FANOUT4 CPU_FAN2 FANPWR2 GND FANOUT4 CPU_FAN2 REAR_FAN1 Rotation +12V GND FRNT_FAN1 FRNT_FAN2 REAR_FAN2 P5CR-VM REAR_FAN2 Rotation +12V GND REAR_FAN1 FRNT_FAN1 Rotation +12V GND FRNT_FAN2 Rotation +12V GND P5CR-VM Fan connectors ASUS P5CR-VM 2-27 5. Hard disk activity LED connector (4-pin HDLED1) This connector supplies power to the hard disk activity LED. The read or write activities of any device connected to the primary/secondary SCSI connectors or the SATA connectors cause this LED to light up. HDLED1 1 P5CR-VM P5CR-VM SCSI/SATA card activity LED connector 6. USB connectors (10-1 pin USB34, USB56, USB78) These connectors are for USB 2. 0 ports. Connect the USB module cables to these connectors, then install the module to a slot opening at the back of the system chassis. The USB connectors comply with USB 2. 0 specification that supports up to 480 Mbps connection speed. USB34 USB+5V USB_4USB_4+ GND NC SCSI_ACTLED+ SCSI_ACTLEDSCSI_ACTLEDSCSI_ACTLED+ USB56 USB+5V USB_6USB_6+ GND NC USB78 USB+5V USB_8USB_8+ GND NC USB+5V USB_7USB_7+ USB+5V P5CR-VM USB+5V USB_3USB_3+ USB+5V P5CR-VM USB 2. 0 connectors Never connect a 1 3 9 4 c a b l e to the USB connectors. Doing so will damage the motherboard! 2-28 Chapter 2: Hardware information USB+5V USB_5USB_5+ USB+5V 7. 42V S S I power connectors (24-pin ATXPWR1, 4- p i n A T X 1 2V 1 ) These connectors are for SSI power supply plugs. The power supply plugs are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit. · Use of an SSI 12 V Specification 2. 0-compliant power supply unit (PSU) that provides a minimum power of 450 W is recommended for a fully-configured system. Do not forget to connect the 4-pin ATX +12 V power plug; otherwise, the system will not boot up. Use of a PSU with a higher power output is recommended when configuring a system with more power consuming devices. This LED is synchronized with the LAN2 LED. Locator Button/Switch (2-pin LOCATORBTN) This connector is for the locator button. This button queries the state of the system locator. Front Panel SMBus (6-1 pin) This connector allows you to connect SMBus (System Management Bus) devices. Devices communicate with an SMBus host and/or other SMBus devices using the SMBus interface. 2-33 ASUS P5CR-VM 1 4 . System panel connector (20-pin PANEL1) This connector supports several chassis-mounted functions. PANEL1 P5CR-VM P5CR-VM System panel connector The sytem panel connector is color-coded for easy connection. · · · System power LED (Green 3-pin PLED) This 3-pin connector is for the system power LED. Connect the chassis power LED cable to this connector. The system power LED lights up when you turn on the system power, and blinks when the system is in sleep mode. Hard disk drive activity LED (Red 2-pin HDLED) This 2-pin connector is for the HDD Activity LED. Connect the HDD Activity LED cable to this connector. The IDE LED lights up or flashes when data is read from or written to the HDD. [. . . ] See section "2. 6 Jumpers" for information on how to erase the RTC RAM. After you have set a supervisor password, the other items appear to allow you to change other security settings. Security Settings Supervisor Password User Password : Not Installed : Not Installed [Full Access] [Setup] [Disabled] <Enter> to change password. <Enter> again to disabled password. Change Supervisor Password User Access Level Change User Password Clear User Password Password Check Boot Sector Virus Protection User Access Level (Full Access] This item allows you to select the access restriction to the Setup items. Configuration options: [No Access] [View Only] [Limited] [Full Access] N o A c c e s s prevents user access to the Setup utility. V i e w O n l y allows access but does not allow change to any field. [. . . ]