User manual ASUS VS238N

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit. This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. [. . . ] Up/Down: Moves the image vertically (up or down). Narrow/Wide: Increases or decreases the horizontal size of the image. Tall/Short: Increases or decreases the vertical size of the image. Geometry Controls Geometry Controls Menu The Geometry controls allow you to adjust the curvature or angle of the sides of your display. Sides In/Out (pincushion): Increases or decreases the curvature of the sides either inward or outward. The icons control the following: Brightness/Contrast Controls Brightness: Adjusts the overall image and background screen brightness. Contrast: Adjusts the image brightness in relation to the background. 78131791 12 7/29/98, 9:24 AM Sides Left/Right (pincushion balance): Increases or decreases the curvature of the sides either to the left or right. Sides Tilt (parallelogram): Increases or decreases the tilt of the sides either to the left or right. Sides Align (trapezoidal): Increases or decreases the bottom of the screen to be the same as the top. Note on Controls in the Geometry Controls Menu: Exit: Exits to the main menu. Cursor / : Moves the highlighted area up/down to select one of the choices. Cursor +/­: Moves the bar in the + or ­ direction to increase or decrease the adjustment. (Positive/Negative) (TTL Level) Unlimited number of Colors 31 kHz to 82 kHz 55 Hz to 100 Hz Notes 90° deflection, 0. 25 mask pitch, medium-short persistence phosphor, CRT, Invar Shadow Mask, multi-layered, anti-static screen coating and OptiClear® screen surface Input Signal Display Colors Synchronization Range Resolutions Supported Analog input: Horizontal: Vertical: Depends on display card used Automatically Automatically 640 x 480 @ 60 to 100 Hz Some systems may not support all modes 800 x 600 @ 55 to 100 Hz listed. 832 x 624 @ 55 to 100 Hz 1024 x 768 @ 55 to 100 Hz 1152 x 870 @ 55 to 75 Hz 1280 x 1024 @ 55 to 75 Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ASUS cites recommended resolution at 75 Hz for optimal display performance. 13 78131791 15 7/29/98, 9:24 AM 14 Specifications MultiSync® XV17+TM Monitor 306 x 230 mm 12. 0 x 9. 1 inches 316 x 237 mm 12. 4 x 9. 3 inches AC 100 ­ 120 V, 50/60 Hz 2. 0 Amps 407 mm (W) x 424 mm (H) x 450 mm (D) 16. 0 inches (W) x 16. 7 inches (H) x 17. 7 inches (D) 20. 0 kg 44. 1 lbs Operating Temperature: Humidity: Feet: Storage Temperature: Humidity: Feet: 0°C to +35°C 30% to 80% 0 to 10, 000 Feet -20°C to +60°C 10% to 90% 0 to 45, 000 Feet NOTE: Technical specifications are subject to change without notice. Monitor Specifications Active Display Area (Factory Setting) Active Display Area (Full Scan) Power Supply Current Rating Dimensions Weight Environmental Considerations Notes Dependent upon signal timing used, and does not include border area. Dependent upon signal timing used, and does not include border area. 78131791 16 7/29/98, 9:24 AM Recommended Use For optimum performance, please note the following when setting up and using the MultiSync® XV17+TM monitor: · If possible, position the monitor so that it is facing east to minimize the effects of the earth's magnetic field. · Allow adequate ventilation around the monitor so that heat can properly dissipate. Do not put anything on top of the monitor. · Do not place any heavy objects on the power cord. Damage to the cord may cause shock or fire. · Changing the direction the monitor is facing while it is powered on may cause image discoloration. To correct this, turn the monitor off for 20 minutes before powering it back on. · Keep the monitor away from high capacity transformers, electric motors and other devices such as external speakers or fans which may create strong magnetic fields. · Use the monitor in a clean and dry area. [. . . ] Any Product on which the serial number has been defaced, modified or removed. What ASUSTECH Will Pay For and What We Will Not Pay For ASUSTECH will pay labor and material expenses for covered items, but we will not pay for the following: 1. Removal or installation charges. 78131791 26 7/29/98, 9:24 AM 2. Costs of initial technical adjustments (setup), including adjustment of user controls. Payment of shipping and related charges incurred in returning the Product for warranty repair. [. . . ]