User manual ASUS VW190NE

[. . . ] 3 Quick Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Using the Monitor Setting the Timing Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 OSD Lock Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Adjusting the Screen Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · OSD Lock: Press and hold the [1] and [] buttons on the face of the monitor for 5 seconds. The message "OSD LOCK" will then display briefly, indicating that the OSD image settings are now locked. · OSD Unlock: Press and hold the [1] and [] buttons again for 5 seconds. The message "OSD UNLOCK" will then display briefly, indicating that the OSD image settings are now unlocked. ViewSonic P95f+-2 5 Adjusting the Screen Image Use the buttons on the front control panel to display and adjust the OnView® controls which display on the screen. The OnView controls are explained at the top of the next page and are defined in "Main Menu Controls" on page 8. Main Menu With OnView controls Front Control Panel Switch Between Normal, UltriBrite 3x, UltraBrite 4x modes "NORMAL: TEXT/SPREADSHEET" : When selected, this brightness level setting displays a standard CRT brightness of 120 nits for text and spreadsheet li ti "ULTRABRITE 3x: GRAPHICS/GAME" ===> When selected, this UltraBrite(tm) setting displays up to 300 nits of brightness for optimum display performance of graphics applications and games. "ULTRABRITE 4x: VIDEO/MOVIE/DVD" ===> When selected, this UltraBrite(tm) setting displays up to 400 nits of brightness for optimized display performance of video applications. Power Light Power On/Off Displays Main Menu; also saves changes/ exits Main Menu. Scrolls through menu options and adjusts the displayed control. Displays control screen for highlighted control (or pair of controls). Also, toggles between pairs of controls on some control screens. P95f+-2 6 ViewSonic Do the following to adjust the screen image: 1 To display the Main Menu, press button [1]. 2 To select a control you want to adjust, press the arrow buttons on the front control panel of your monitor and scroll through the choices. When the control you want is highlighted, press button [2]. NOTE: Some controls on the Main Menu are listed in pairs, such as Contrast/Brightness. Display control screen (sample shown in step 3 below). · Remove any devices from the area around the monitor that emit magnetic fields such as radios, surge protectors, unshielded speakers, fluorescent lights, AC power converters, desk fans, etc. · Make sure the graphics card in your computer can use non-interlaced mode at the desired frequencies. To enable your graphics card to support higher refresh rates, try selecting fewer colors or running lower resolutions. Wrong or abnormal colors · If any colors (red, green, or blue) are missing, check the video cable to make sure it is securely connected. Loose or broken pins in the cable connector could cause an improper connection. · Connect the monitor to another computer. · Select Degauss from the Main Menu. · If you have an older graphics card, contact ViewSonic® Customer Support. Entire screen image rolls vertically · Make sure video input signals are within the monitor's specified frequency range. · Try the monitor with another power source, graphics card, or computer system. · Connect the video cable securely. [. . . ] Use the following guidelines if it is necessary to replace the original cord set, or if the cord set is not enclosed. The female receptacle of the cord set must meet IEC-60320 requirements and may look like (Figure A1 below): For the United States and Canada In the United States and Canada the male plug is a NEMA5-15 style (Figure A2), UL Listed, and CSA Labeled. For units which are mounted on a desk or table, type SVT or SJT cord sets may be used. For units which sit on the floor, only SJT type cord sets may be used. [. . . ]