User manual ASUS VW193DR-A

[. . . ] Others are copyrights of their respective companies or organizations. Table of Contents Important safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Projector features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Shipping contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Optional accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Projector exterior view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Front / Upper side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Rear side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Lower side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Controls and functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The password can be set through the on-screen menu. For details of the on-screen menu operation, please refer to "Using the menus" on page 29 for information. WARNING: You will be inconvenienced if you activate the password functionality and subsequently forget the password. Print out this manual and write the password you used in this manual, and keep the manual in a safe place for later recall. To set a password CAUTION: Once a password has been set, the projector cannot be used unless the correct password is entered every time the projector is started. 1. Open the on-screen menu and go to the3Left or4Right button. Setting > Password. Select On by pressing 2. Password Setup When the function is activated for the first time, a prompt will display on the screen. Use the 5 Enter Password 0 0 0 0 or 6Down button to select a number for each Press Auto to Confirm digit of the password. Use the3Left or4Right Press 5 or 6 to change number button to move between the digits of the Press 3 or 4to move password. 3. When all digits are entered and the password is ready, press the AUTO button to confirm. A confirmation message displays. Password Setup Do you want to use 0 0 0 0 as your password?Yes Auto No 5 Cancel 6 · · The password will display on-screen when being input. IMPORTANT: Write your selected password down here in this manual so that it is available to you should you ever forget it. Password: __ __ __ __ Keep this manual in a safe place. 4. · · · You have the following options: Press AUTO to continue. Within 3 seconds, the built-in Intelligent Auto Adjustment function will re-adjust the values of Frequency and Clock to provide the best picture quality. The current source information will be displayed at the bottom right of the screen for 3 seconds. The screen will be blank while Auto is functioning. Fine-tuning the image size and clarity 1. Adjust the projected image to the size that you need using the zoom ring. Then sharpen the image by rotating the focus ring. Refer to the screen size tables in "Obtaining a preferred projected image size" on page 12. Correcting keystone Keystoning refers to the situation where the projected image is noticeably wider at either the top or bottom. It occurs when the projector is not perpendicular to the screen. Manual keystone correction To correct keystoning manually, you can perform the following steps. Adjust the projection angle of the projector. If the image is still distorted, you will need to manually correct it following ONE of these steps. Press the Keystone /3Left or Keystone /4Right buttons on the control panel of the projector to display the status bar labelled Keystone. Press the · 24 Using the projector Keystone Keystone · Press the / /3Left button to correct keystoning at the top of the image. Press the /4Right button to correct keystoning at the bottom of the image. buttons on the remote control to display the status bar labelled button to correct keystoning at the top of the image or Keystone, then press the · press the button to correct keystoning at the bottom of the image. [. . . ] The lens cover is not open. Remedy Turn the video source on and check that the signal cable is connected correctly. See "Connection" on page 16 for details. See "Connection" on page 16 for details. Select the correct input signal with the SOURCE button on the projector or remote control. [. . . ]