User manual ASUS W2W

[. . . ] Hardware User's Manual Notebook PC E3104 / Apr 2007 Contents Table of Contents Table of Contents 1. Introducing the Notebook PC About This User's Manual 6 Notes For This Manual 6 Preparing your Notebook PC 9 2. Knowing the Parts Top Side 12 Bottom Side 14 Left Side 16 Right Side 18 Front Side 20 Rear Side 22 3. Getting Started Power System 24 Using AC Power 24 Using Battery Power 25 Battery Care 25 Powering ON the Notebook PC 26 The Power-On Self Test (POST) 26 Checking Battery Power 27 Charging the Battery Pack 27 Power Options 28 Power Management Modes 29 Sleep and Hibernate 29 Thermal Power Control 29 Special Keyboard Functions 30 Colored Hot Keys 30 Microsoft Windows Keys 32 Keyboard as a Numeric Keypad 32 Keyboard as Cursors 32 2 Contents Table of Contents (Cont. ) Switches and Status Indicators 33 Switches 33 Status Indicators 34 Multimedia Control Keys (on selected models) 36 4. [. . . ] (Self Monitoring and Reporting Technology) to detect hard disk errors or failures before they happen. When replacing or upgrading the hard drive, always visit an authorized service center or retailer for this Notebook PC. Poor handling of the Notebook PC may damage the hard disk drive. Handle the Notebook PC gently and keep it away from static electricity and strong vibrations or impact. The hard disk drive is the most delicate component and will likely be the first or only component that is damaged if the Notebook PC is dropped. 1 2 3 9 Hard Disk Drive Compartment 4 10 The hard disk drive is secured in a compartment. Visit an authorized service center or retailer for information on hard disk drive upgrades for your Notebook PC. Only purchase hard disk drives from authorized retailers of this Notebook PC to ensure maximum compatibility and reliability. 7 44 Using the Notebook PC Memory (RAM) 4 Additional memory will increase application performance by decreasing hard disk access. The BIOS automatically detects the amount of memory in the system and configures CMOS accordingly during the POST (Power-On-Self-Test) process. There is no hardware or software (including BIOS) setup required after the memory is installed. 1 2 3 This is only an example 5 The memory compartment provides expansion ca4 10 pabilities for additional memory. Visit an authorized service center or retailer for information on memory upgrades for your Notebook PC. Only purchase expansion modules from authorized retailers of this Notebook PC to ensure maximum compatibility and reliability. 7 Installing a Memory Card: Removing a Memory Card: 3 (This is only an example) (This is only an example) 4 4 Connections Using the Notebook PC NOTE: The built-in modem and network cannot be installed later as an upgrade. After purchase, modem and/or network can be installed as an expansion card. Modem Connection The telephone wire used to connect the Notebook PC's internal modem should have either two or four wires (only two wires (telephone line #1) is used by the modem) and should have an RJ-11 connector on both ends. Connect one end to the modem port and the other end to an analog telephone wall socket (the ones found in residential buildings). Once the driver is setup, the modem is ready to use. NOTE: When you are connected to an online service, do not place the Notebook PC in suspend (or sleep mode) or else you will disconnect the modem connection. ExampleoftheNotebookPCconnectedtoatelephonejackforusewiththebuilt-inmodem: Telephone connector is the smaller of the two Telephone Wall Jack Telephone connection is optional Telephone cables with RJ-11 connectors CAUTION: For electrical safety concerns, only use telephone cables rated 2AWG or higher. (see Glossary for more information) WARNING!The built-in modem does not support the voltage used in digital phone systems. Do not connect the RJ-11 to digital phone systems found in many commercial buildings or else damage will occur! 4 Using the Notebook PC Network Connection 4 Connect a network cable, with RJ-45 connectors on each end, to the modem/network port on the Notebook PC and the other end to a hub or switch. For 100 BASE-TX / 1000 BASE-T speeds, your network cable must be category 5 or better (not category 3) with twisted-pair wiring. If you plan on running the interface at 100/1000Mbps, it must be connected to a 100 BASE-TX / 1000 BASE-T hub (not a BASE-T4 hub). For 10Base-T, use category 3, 4, or 5 twisted-pair wiring. [. . . ] WARNING: Making adjustments or performing procedures other than those specified in the user's manual may result in hazardous laser exposure. Do not attempt to disassemble the optical drive. For your safety, have the optical drive serviced only by an authorized service provider. Service warning label CAUTION: INVISIBLE LASER RADIATION WHEN OPEN. DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS. CDRH Regulations The Center for Devices and Radiological Health (CDRH) of the U. S. [. . . ]