User manual ASUS W7SG EXPRESS GATE QUICK START GUIDE

[. . . ] IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. ii Contents FCC/CDC statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The system message LED feature requires an ACPI OS and driver support. · System Management Interrupt Lead (2-pin SMISW) This 2-pin connector allows you to manually place the system into a suspend mode, or "green" mode, where system activity is instantly decreased to save power and to expand the life of certain system components. Attach the case-mounted suspend switch to this 2-pin connector. ASUS W7SG motherboard user guide 2-37 Reset Ground W7SG · ATX Power Switch / Soft-Off Switch Lead (2-pin PWRSW) This connector connects a switch that controls the system power. Pressing the power switch turns the system between ON and SLEEP, or ON and SOFT OFF, depending on the BIOS or OS settings. Pressing the power switch while in the ON mode for more than 4 seconds turns the system OFF. · Reset Switch Lead (2-pin RESET) This 2-pin connector connects to the case-mounted reset switch for rebooting the system without turning off the system power. 2-38 Chapter 2: Hardware information Chapter 3 This chapter describes the power up sequence and gives information on the BIOS beep codes. Powering up ASUS W7SG motherboard 3. 1 Starting up for the first time 1. After making all the connections, replace the system case cover. Connect the power cord to the power connector at the back of the system chassis. Connect the power cord to a power outlet that is equipped with a surge protector. Turn on the devices in the following order: a. · Check if the DIMMs on the DIMM sockets are properly installed. · Make sure that your DIMMs are not defective. · Refer to section "2. 3 System memory" for instruction on installing a DIMM. · Install a PCI VGA card into one of the PCI slots, or a 1. 5V AGP card into the AGP slot. · Make sure that your VGA/AGP card is not defective. · In JumperFree mode, check your CPU settings in BIOS and make sure you only set to the recommended settings. See section "4. 4 Advanced menu. " · In jumper mode, refer to section "2. 7 Switches and jumpers. " System failed CPU test System failed memory test System failed VGA test System failed due to CPU over-clocking 3-2 Chapter 3: Powering up POST Message No keyboard detected Action · Check your keyboard if properly connected to the purple PS/2 connector on the rear panel. · See section "1. 3. 1 Identifying the motherboard components" for the location of the connector. · Make sure you have connected a floppy disk to the floppy disk connector on the motherboard. · See section "2. 8 Connectors. " · Make sure you have connected an IDE hard disk drive to the one of the IDE connectors on the motherboard. · See section "2. 8 Connectors. " · Check CPU fan if working properly. [. . . ] Click Yes on the confirmation window that appears. The next time you boot your computer, the POST messages are announced in the language that you selected . ASUS W7SG motherboard user guide 5-15 Customizing your POST messages If your language is not in the selection or if you wish to record your own POST messages to replace the pre-installed wave files, you may easily do so. Follow these steps to customize your POST messages. Launch the Voice Editor and take note of the list of POST events on the leftmost column of the screen. [. . . ]