User manual ASUS X59SR EXPRESS GATE QUICK START GUIDE

[. . . ] The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. FCC NOTICE · A Class B digital device This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] · Flat, Music, Movie and Sports are preset for good sound quality at the factory and cannot be changed. Manual Sound Control (User option) ( - You can adjust sound treble, bass, and balance to the levels you prefer. 1. Press the MENU button and then use D 2. Press the G button and then use (Balance, Treble, Bass). Press the G D /E /E button to select the SOUND menu. AVL SOUND DASP button to select the desired sound option button and then use F /G button to make appropriate adjustments. Balance Treble Bass 0 50 50 G 4. Press the ENTER button to save. MENU Prev. AVL (Auto Volume Leveler) - AVL maintains an equal sound level; even if you change channels. Press the G G D /E button to select the SOUND menu. AVL SOUND DASP G button and then use button and then use D /E D /E button to select A VL. button to select On or Off. On Off Balance Treble Bass 0 50 50 4. Press the ENTER button to save. MENU Prev. Owner's Manual 17 Operation T imer Menu Options Clock Setup - If current time setting is erased by a power failure, if TV is unplugged or if the monitor is turned off with the ON/OFF button on the monitor, reset the clock. Press the G G G D /E button to select the TIMER menu. TIMER Clock Off timer On timer Auto off G button and then use button and then use button and then use D /E D /E D /E button to select Clock. button to set the minutes. -- : -- 5. Press the ENTER button to save. MENU Prev. On/Of f Timers Setup - Timer functions operate only if current time has been set. · With the KEY LOCK ON, the display ` button on the front panel is pressed. Key lock' appears on the screen if any Set ID Caption / Text Captions OSD Rotate MENU Prev. ISM (Image Sticking Minimization) Method - A frozen still picture from a PC/video game displayed on the screen for prolonged periods will result in a ghost image remaining even when you change the image. Avoid allowing a fixed image to remain on the Monitor's screen for a long period of time. Press the G G D /E button to select the SPECIAL menu. SPECIAL Language Key lock button and then use D /E D /E button to select ISM Method. button to select either Normal, White button and then use wash, Orbiter, or Inversion. ISM Method Low power Set ID Caption / Text Captions OSD Rotate MENU Prev. G Normal White wash Orbiter Inversion · Normal: If image sticking is never a problem, ISM is not necessary - set to Normal. · White wash White Wash removes permanent images from the screen. Note: An excessive permanent image may be impossible to clear entirely with White Wash. To return to normal viewing, press the any button. · Orbiter Orbiter may help prevent ghost images. However, it is best not to allow any fixed image to remain on the screen. To avoid a permanent image on the screen, the screen will move every 1 minutes: Right Right Downside Downside Left Left Upside Upside. · Inversion Inversion will automatically invert the plasma display panel color every 30 minutes. [. . . ] Abnormal State (Command2:z) G To recognize an abnormal state. Transmission [k][z][ ][Set ID][ ][FF][Cr] Data FF:Read Acknowledgement [z][ ][Set ID][ ][OK][Data][x] Data 0: Normal (Power on and signal exist) 1: No signal (Power on) 2: Turn the monitor off by remote control 3: Turn the monitor off by sleep time function 4: Turn the monitor off by RS-232C function 5: 5V down 6: AC down 7: Turn the monitor off by Fan Alarm function 8: Turn the monitor off by off time function 9: Turn the monitor off by auto off function a: Turn the monitor off by AV board detect G To adjust pixel number in orbiter function. Transmission [j][s][ ][Set ID][ ][Data][Cr] Data Min: 0 ~ Max: 9 Acknowledgement [s][ ][Set ID][ ][OK][Data][x] 31. Picture Size Setting for Double Window mode (Command2:t) G To adjust main window size in Double Window mode. [. . . ]