User manual ASUS X81L EXPRESS GATE QUICK START GUIDE

[. . . ] Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. · QuickStart and JumperFree are trademarks of ASUSTeK Computer Inc. · Intel, LANDesk, and Pentium are registered trademarks of Intel Corporation. · IBM and OS/2 are registered trademarks of International Business Machines. [. . . ] You can also restart by turning the system OFF and then back ON again. But do so only if the first two methods fail. The Setup program has been designed to make it as easy to use as possible. It is a menu-driven program, which means you can scroll through the various sub-menus and make your selections among the predetermined choices. To access the BIOS Setup program, press the <Delete> key after the computer has run through its POST. NOTE: Because the BIOS software is constantly being updated, the following BIOS screens and descriptions are for reference purposes only and may not reflect your BIOS screens exactly. ASUS X81L User's Manual 49 4. BIOS SETUP 4. 2. 1 BIOS Menu Bar The top of the screen has a menu bar with the following selections: MAIN Use this menu to make changes to the basic system configuration. ADVANCED Use this menu to enable and make changes to the advanced features. POWER Use this menu to configure and enable Power Management features. BOOT Use this menu to configure the default system device used to locate and load the Operating System. EXIT Use this menu to exit the current menu or specify how to exit the Setup program. NOTE: The item heading in square brackets represents the default setting for that field. ASUS X81L User's Manual 51 4. BIOS SETUP 4. 3 Main Menu When the Setup program is accessed, the following screen appears: System Time [XX:XX:XX] Sets your system to the time that you specify (usually the current time). Valid values for hour, minute and second are Hour: (00 to 23), Minute: (00 to 59), Second: (00 to 59). Use the <Tab> or <Shift> + <Tab> keys to move between the hour, minute, and second fields. System Date [XX/XX/XXXX] Sets your system to the date that you specify (usually the current date). Valid values for month, day, and year are Month: (1 to 12), Day: (1 to 31), Year: (100 year range). Use the <Tab> or <Shift> + <Tab> keys to move between the month, day, and year fields. Legacy Diskette A [1. 44M, 3. 5 in. ], Legacy Diskette B [None] Sets the type of floppy drives installed. Configuration options: [None] [360K, 5. 25 in. ] [1. 2M , 5. 25 in. ] [720K , 3. 5 in. ] [1. 44M, 3. 5 in. ] [2. 88M, 3. 5 in. ] Floppy 3 Mode Support [Disabled] This is required to support older Japanese floppy drives. Floppy 3 Mode support will allow reading and writing of 1. 2MB (as opposed to 1. 44MB) on a 3. 5-inch diskette. Configuration options: [Disabled] [Drive A] [Drive B] [Both] 4. [. . . ] With this software modem, you can connect your computer to a remote location, receiving data at up to 56 Kbps in V. 90 or K56flex modes. Layout of Primary MR 7. APPENDIX Modem Riser 119 7. 3. 2 Primary/Seconday MR There are two types of modem risers: primary MR and secondary MR. In appearance, the primary MR has a crystal onboard but the secondary does not. If your motherboard has an audio codec and no PCI audio chipset onboard, you may use the secondary MR; otherwise, you should use the primary MR. Top: Codec PHONE Bottom: LINE Crystal 7. 3. 3 Hardware Installation Procedure 1. [. . . ]