User manual ASUS Z9NA-D6

[. . . ] No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe. 5-17 Checking the drives for data consistency. [. . . ] Xx [Disabled] [10 minutes] [Reset] Wait for BMC response for specified timeout In PILOTII, BMC starts at the same time when BIOS starts during AC power ON. It takes arround 30 seconds to initialize Host to BMC interfaces. O/S Watchdog Timer [Disabled] If enabled, starts a BIOS timer which can only be shut off by Intel Management Software after the OS loads. Helps determine that the OS sucessfully loaded or follows the O/S Boot Watchdog TImer Policy. Configuration options: [Enabled] [Disabled] O/S Wtd Timer Timeout [10 minutes] Allows you to configure the length of the O/S Boot Watchdog Timer. not available if O/S Boot Watchdog Timer is disabled. Configuration options: [5 minutes] [10 minutes] [15 minutes] [20 minutes] O/S Wtd Timer Policy [Reset] Allows you to configure how the system should respond if the OS Boot Watchdog Timer expires. Server Mgmt Change this to enable or disable all features of system Event Logging during boot. Enabling/Disabling Options SEL Components Erasing Settings Erase SEL When SEL is Full [Disabled] [No] [Do Nothing] Note: ll values changed here do not take effect A until computer is restarted. SEL Components [Disabled] Allows you to enable or disable all features of system Event Logging during boot. Configuration options: [Disabled] [Enabled] • • The following items appears only when you set SEL Components to [Enabled]. All values changed here do not take effect until computer is restarted. Erase SEL [No] Allows you to choose options for erasing SEL. Configuration options: [No] [Yes, On next reset] [Yes, On every reset] When SEL is Full [Do Nothing] Allows you to choose options for reactions to a full SEL. Unspecified option will not modify any BMC network parameters during BIOS phase BMC network configuration Lan1 Lan1 Lan1 Lan1 Lan1 Lan1 IP Address in BMC: Subnet Mask in BMC: Gateway Address in BMC: MAC Address in BMC: Address Source in BMC: 000. Unspecified option will not modify any BMC network parameters during BIOS phase. Configuration options: [Previous State] [Static Mode] [DHCP Mode] The following items appears only when you set Configuration Address source to [Static Mode]. The Event Logs allows you to change or view the event log settings. F1: General Help F2: Previous Values F5: Optimized Defaults F10: Save & Exit ESC: Exit Change this to enable or disable all features of Smbios Event Logging during boot. Smbios Event Log Standard Settings Log System Boot Event [Disabled] MECI 1 METW 60 Custom Option Log OEM Codes [Enabled] Convert OEM Codes [Disabled] Note: ll values changed here do not take effect A until computer is restarted. All values changed here do not take effect until computer is restarted. Enabling/Disabling Options Smbios Event Log [Enabled] Change this to enable or disable all features of Smbios Event Logging during boot. [. . . ] If Autorun is NOT enabled in your computer, browse the contents of the support DVD to locate the file AUTORUN. EXE and follow step 4 to run the installation. Restart the computer, and then log on with Administrator privileges. When the Intel® Network Connections – InstallShield Wizard window appears, click Next to start the installation. [. . . ]