User manual AT&T 1717

[. . . ] The Message Window flashes C to indicate that you need to set the clock. Use only the power cord supplied with this product. If you need a replacement, call 1 800 222­3111. Output: 9V AC, 400 mA. 1 OPERATION Displays number of messages and other information Adjust volume Set and hear time/day Use with other buttons to change/hear settings Turn system on or off Delete all or selected messages Record and play outgoing announcement / Skip all or part of a message Microphone Record a memo / Repeat all or part of a message Play/Stop messages PLAY Light indicates messages Setting the Clock You'll need to set the clock so that it can announce the day and time that each message is received. [. . . ] 5 Press P to exit -- OR -- Press S to turn the Announcement Monitor on or off (follow Steps 2 and 3 under "Announcement Monitor"). Call Screening/Intercept Set the system to answer calls, and set the volume control so you can hear the caller's message. If you choose not to hear the caller's message, adjust the volume to the lowest setting. If you decide to take the call, lift the handset of any telephone on the same line. The system stops recording and resets to answer calls. Feature Set Up You can set up one feature at a time as described below, or you can set up a feature, and then move on to set up another feature. After you change one feature, press and release S until you hear the voice prompt for the next feature you want to change -- OR -- 3 OPERATION Announcement Monitor You can choose whether to hear the announcement when your system answers a call, or have it silent (off) on your end (your caller will still hear an announcement). After the Ring Select setting is announced, continue to press and release S until the system announces "Monitor is on (or off)". or 2 Press and release until the system announces your selection. 3 Press and release P or S to exit. Saving Messages The system automatically saves your messages if you do not delete them. The system can save about 12 minutes of messages, including your announcement, for a total of up to 59 messages. When memory is full, you must delete some or all messages before new messages can be recorded. Deleting Messages Delete all messages -- Hold down D. The system announces "Messages deleted" and permanently deletes messages. If you haven't listened to all of the messages, the system beeps five times, and does not delete messages. Delete selected messages -- Press and release D while the message you want to delete is being played. The system beeps once, and continues with the next message. If you want to check a message before you delete it, you can press to replay the message before deleting it. When the system reaches the end of the last message, the messages not deleted are renumbered, and the Message Window displays the total number of messages remaining in memory. Listening to Your Messages As the system plays back messages, the Message Window displays the number of the message playing. Before playing each message, the system announces the day and time the message was received. After playing the last message, the system announces "End of messages. " Play all messages -- Press and release P. If you have no messages, the system announces "No messages. " Play new messages only -- Hold down P for about two seconds, until the system begins playing. If you have no new messages, the system announces "No new messages. " Repeat entire message -- Press and release . Repeat part of message -- Hold down until you hear a beep, then release to resume playing. The more beeps you hear, the farther back in the message you will be when you release the button. [. . . ] Call 1 800 222­3111. · · System Will Not Record Messages When memory is full and the Message Window displays F, saved messages must be deleted before new messages can be recorded. 7 1 Tapeless Digital Answering System 1717 Remote Commands To connect with your answering system: 1 Dial your telephone number from a touch tone phone. 2 When the system answers, enter your Remote Access Code. The system announces the number of messages and beeps twice. 3 Wait four seconds for the system to play back all messages -- OR -- Enter a remote command from inside this card. 1 Tapeless Digital Answering System 1717 Remote Commands To connect with your answering system: 1 Dial your telephone number from a touch tone phone. [. . . ]