User manual AT&T 1854

[. . . ] 2 Digital Answering System Telephone with Caller ID and Speakerphone 1854 Fold open this paper for information about this product's installation and operation. Please read Part 1 -- Important Product Information, included in this package. NEW CALL 1854 CALL LIST A WB R TTE Y LO RE MO VE DIS Y PLA DIA L SELE CT ANNC CLOCK ON/OFF FEAT URE RECORD FWD DELETE PLAY STOP RE PEA T LOWER THIS NUMBER ABC DEF (AUTO) REDIAL PROG RAM 1 GHI 2 JKL 3 MNO VOLUME FL ASH 4 PQRS 5 TUV 6 WXYZ MUTE 7 TONE 8 OPER 9 SPEAKER HOLD * 0 # Part 2 © 1998 Philips Consumer Communications L. P. 848229415 Issue 1AT&T INSTALLATION Remove the Base Install the Batteries Press in on tabs. Open battery compartment door Install 4 AA batteries Lift base off the phone. SET UP SYSTEM 1 Install the batteries. · Push in on the two tabs at the large end of the base, and lift the base off the phone. [. . . ] If you select AO, you must record an announcement, as instructed in "Record an Announcement. " 3 Press S to return to the message display. REVIEW CALL MATCH ANNOUNCEMENT 1 Press A. 2 Press and release S until the screen displays CALL MATCH. 4 Press S when you are done -- OR -- Press D while the announcement is playing to delete it. SET SYSTEM TO ANSWER CALLS To turn the system on or off, press O. RING SELECT 1 Press and release F until the screen displays RING SELECT. 2 Use the keypad to select the number of times (1 to 7) the phone will ring before the system answers a call. For example, to select 3 rings, press 3. 3 To select the Toll Saver, press 8 to have the system ring 4 times when there are no new messages, and 2 times when there are messages -- OR -- Press 9 to have the system ring 6 times when there are no new messages, and 4 times when there are messages. 4 Press S when you are done. RING SELECT FOR CALL MATCHING 1 Press A. 2 Press and release S until the screen displays CALL MATCH. 4 Use the keypad to select the number of times (1 to 7) the phone rings before the system answers. To choose Toll Saver, press 8 for 4 rings/2 rings; press 9 for 6 rings/4 rings. (For more information about Toll Saver, see "Ring Select. ") RECORD AN ANNOUNCEMENT 1 Prepare your announcement. Each announcement can be up to 4 minutes long. 3 Press and release S until you see the letter of the announcement you want to record (A, B, or O). Speak in a normal tone of voice, about 9 inches from the microphone. To hear the announcement again, press P. 6 Repeat Steps 3 to 5 to record another announcement, or press S. ANSWERING SYSTEM OPERATION NUMBER OF CALLS ANSWERED BY CALL MATCHING 1 Press A. 2 Press and release S until the screen displays CALL MATCH. 4 Use the keypad to enter the number of calls (1 to 9) for which you want to the announcement played. Press # if you always want the announcement played. 5 Press S. SAVE/DELETE MESSAGES The system can save about 20 minutes of announcements and messages, up to a total of 50 messages. To delete messages, hold down D until the system announces "Messages deleted. " If there are new messages among those you are trying to delete, the system beeps 5 times and does not delete any. CHANGE PRIORITY CALLING CODE The Priority Calling Code is preset to 999. 1 Press and release F until the screen displays P CALLING CODE. [. . . ] j If the ON/OFF light flashes rapidly, memory might be full. j If the ON/OFF light flashes rapidly, the system might be set to Announce Only (AO), and no announcement is recorded. If you recorded Announcement AO, it might have been lost because of a power failure. Either record a new Announcement AO, or switch to a different announcement. [. . . ]