User manual AT&T 260

[. . . ] 260book_1ATT 4/24 4/24/02 6:24 PM Page ii 1 USER'S MANUAL Part 2 Trimline® Caller ID Telephone 260 REVISED DRAFT 4/24/02 Please also read Part 1 -- Important Product Information AT&T and the Globe Design are registered trademarks of AT&T Corp. licensed to Advanced American Telephones. 260book_1ATT 4/24 4/24/02 6:24 PM Page iii © 2002 Advanced American Telephones. Issue 1AT&T 04/02 260book_1ATT 4/24 4/24/02 6:24 PM Page v CONTENTS BEFORE YOU BEGIN . 1 About Caller Identification (Caller ID) . [. . . ] Repeat Steps 2 and 3 for the second and third digits of your Home Area Code. You will not see or hear confirmation of the new Home Area Code, but the screen will prompt you to set the next feature. 11 260book_1ATT 4/24 4/24/02 6:24 PM Page 12 FEATURE SETTINGS Set Local Area Codes Local Area Codes are area codes associated with other phone numbers for which you must dial the area code, but do not dial "1". This includes your own area code if you must dial the area code but no "1" to make calls in your own area code. You can program up to four Local Area Codes. Do not program area codes for which you must dial a "1". If you dial. . . Then, in Steps 2-4 Make no entry Enter area codes that do not require a "1" Enter your own area code 11 digits All calls outside (1 + area code + phone number) your own area code 10 digits (area code + phone number) 10 digits (area code + phone number) Some calls outside your own area code All calls within your own area code 1 Press and release N until the screen displays: LAC-___ LOCL AREA CODE? 2 3 4 5 6 Press - or + until the screen displays the first digit of the first Local Area Code. Repeat Steps 2 and 3 for the second and third digits of the first Local Area Code. To program another Local Area Code, press D until the screen displays: LAC2-___ LOCL AREA CODE? 7 8 Repeat Steps 2­5 to enter the digits of the next Local Area Code. Press to call the last number dialed (up to 32 digits). Mute Press and hold M to prevent the other party from hearing you (you will still be able to hear the other party). Release M to return to two­way conversation. 15 260book_1ATT 4/24 4/24/02 6:24 PM Page 16 TELEPHONE OPERATION RINGER Volume Adjust how loudly the phone rings. If the RINGER switch is set to OFF, this phone will not ring when you have an incoming call. 16 260book_1ATT 4/24 4/24/02 6:24 PM Page 17 TELEPHONE OPERATION New Call Light This light flashes when you have unreviewed call information in the call history. Clear Line Status Indicator Flashes when you are receiving a call. Remains steady when this phone or another phone on the same line is in use. Press to exit dialing, to exit storing a number in memory, to exit call history or at any time to return to the idle screen without saving any changes. Flash/Call Waiting When you receive a call waiting signal, press F to put your current call on "hold" and connect to the new call. Press F again to return to the first call. Also use F to activate other phone company subscriber services such as 3-Way Calling. 17 260book_1ATT 4/24 4/24/02 6:24 PM Page 18 TELEPHONE MEMORY This telephone can store 13 telephone numbers, each up to 24 digits long. You can dial numbers stored in memory by pressing one or two buttons. NOTE: Numbers stored in memory will be lost if the phone is unplugged from the line jack and there are no charged batteries installed for more than 2. 5 hours. Directory Card Lift the plastic cover off the directory card to write the numbers (or names) stored in telephone memory on the card. Then, replace the plastic cover. 18 260book_1ATT 4/24 4/24/02 6:24 PM Page 19 TELEPHONE MEMORY NOTE: Press on the back of the handset while storing a memory number to exit programming. One-Touch Dialing Two-Touch Dialing For two-touch dialing: 1 Lift the handset. 2 Press and release M, then press the number button (0-9) where the memory number is stored. The number appears on screen as it is dialed. For one-touch dialing, lift the handset and press the memory button. The number appears on screen as it is dialed. Storing a Pause in a Memory Number Press and release once to store a 2. 5-second pause in the dialing sequence, twice for a 5. 0-second delay, three times for a 7. 5-second delay. Storing Memory Numbers NOTE: Each 2. 5 second 1 Lift the handset. pause counts as one digit 2 Press and release p. [. . . ] An extension phone on this line is being used, so call information cannot be received. There is a problem with Caller ID transmission from the telephone company. 23 260book_1ATT 4/24 4/24/02 6:24 PM Page 24 IN CASE OF DIFFICULTY If you have difficulty operating this phone, try the suggestions below. For Customer Service, visit our website at www. telephones. att. com or call 1 800 222­3111. Please retain your receipt as your proof of purchase. No Dial Tone · Make sure all plugs are connected properly. [. . . ]