User manual AT&T 9002

[. . . ] 2 User's Manual for 900 MHz Two-Line Cordless Speakerphone 9002 Part 2 Please read Part 1 -- Important Product Information, included in your package. 9002_cover. 1AT&T 2 8/12/98, 4:03 PM © 1998 Philips Consumer Communications L. P. 848233896 Issue 1AT&T 9002_cover. 1AT&T 1 8/12/98, 4:03 PM CONTENTS INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Table/Desk Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Wall Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Feed the excess line cord under the tab on the bottom of the telephone base. Plug the short line cord into the standard one-line wall jack. Insert one end of the long clear telephone line cord into the telephone jack labeled L2 on the rear of the telephone base. Feed 5 9002_book. 1AT&T 5 8/12/98, 4:09 PM INSTALLATION the excess line cord under the tab on the bottom of the telephone base. Plug the line cord into your other one-line wall jack. Position the telephone base so the mounting studs on the wall jack fit into the base of the telephone. Slide the telephone down on the mounting studs until the phone locks into place. Follow Steps 7 and 8 under Table/Desk Installation. CAUTION: Use only the AC power adapter supplied with this telephone. Input: AC 117V, 60 Hz, 9W Output: DC 9V, 500mA 5 6 Belt Clip If you wish, you can attach the belt clip to the cordless handset, following the illustrations below. To Attach To Remove 6 9002_book. 1AT&T 6 8/12/98, 4:09 PM OPERATION Send a paging tone to handset/ intercom between base and handset Mute the microphone Put a caller on hold Initiate a conference call Adjust speaker volume PULSE/TONE switch and Line 1 and Line 2 RINGER switches on side of base Line 2 ­ Activate speakerphone End a call Line 1 and Line 2 lights flash when handset or extension is in use Line 1 ­ Activate speakerphone Light goes on when handset is charging in the base Light goes on when base is connected to power Directory Card 7 9002_book. 1AT&T 7 8/12/98, 4:09 PM OPERATION Light goes on when intercom is in use Volume HI/LO switch Line 1 ­ Make or answer a call Line 2 ­ Make or answer a call Line 1 and Line 2 buttons flash if base or extension is in use Headset jack Light goes on when handset battery is low End a call Temporary tone Change channel Store and access numbers in telephone memory Connect parties to conference call Begin two-way communication with base Put a caller on hold Redial last number dialed 8 9002_book. 1AT&T 8 8/12/98, 4:09 PM OPERATION Making a Call 1 2 Press and release L or l, and wait for a dial tone. The line button of the line you're using lights. When you hear a dial tone, dial the number. Answering a Call Press and release the flashing L or l button on the handset or the base to answer a call on that line. (You can also answer calls on the handset by pressing any key except o. ) You can answer calls at the handset or at the base speakerphone. If you are on a call on one line, and wish to answer a call on the other line, press the line key of the new call. The first call is automatically put on hold. To return to the first call, press the line key of that call. Pressing o while you're on a line ends the call on that line. Ending a Call Press o on the handset to end a call on the handset -- OR -- Place the handset in the base to end a call on the handset -- OR -- Press o on the base to end a call at the base speakerphone. Redial The last number dialed on this phone (up to 16 digits) is stored in redial memory until you dial another number. 2 When you hear a dial tone, press R. Handset Ringer Selection and Ringer OFF You can select from four different handset ringer styles for each line. You can also turn off one or both ringers. 3 Press 1, 2, 3 or 4 to select your ringer style. You will hear a sample of the ringer style -- OR -- Press 0 to turn the ringer off. 4 Press p. 9 9002_book. 1AT&T 9 8/12/98, 4:09 PM OPERATION Checking Handset Ringer Selection 1 2 3 4 Press p, *. [. . . ] Place the handset in the base and allow it to charge for 16 hours. Your telephone might operate before that, but for best performance, let the handset battery pack charge fully. 17 9002_book. 1AT&T 17 8/12/98, 4:09 PM IN CASE OF DIFFICULTY If you have difficulty operating this phone, try the suggestions below. If you still have trouble, call 1 800 722-9125. If the phone doesn't work at all, check these items first: · · · · · · Make sure the AC adapter is plugged in. Make sure the telephone line cord(s) is plugged firmly into the base unit and the modular telephone jack. [. . . ]