User manual AT&T 9050

[. . . ] 2 User's Manual for Cordless Telephone Answering System 9050 Part 2 Please read Part 1 -- Important Product Information, included in your package. 9050_cover. 1AT&T 3 8/12/98, 4:14 PM © 1998 Philips Consumer Communications L. P. 848232518 Issue 1AT&T 9050_cover. 1AT&T 2 8/12/98, 4:14 PM CONTENTS INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Table/Desk Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Wall Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The system prompts with "On" or "Off. " Press and release S until you hear your choice. Select Off if you want callers to be able to leave a message. Press and release C to confirm your selection. Press and release U to set up another feature -- OR -- Press and release Y to exit. 3 4 Recording Your Announcement 1 2 3 4 Select your announcement (see above). Press and release U until you hear "Set outgoing message. " Press and release M. The system prompts "Now recording. " Begin recording your announcement, up to 90 seconds long. The Message Window shows the elapsed time of your announcement as you record. Record your announcement in a quiet location, away from any background noise. The system plays back your announcement. 5 14 9050_book. 1AT&T 14 8/12/98, 4:14 PM ANSWERING SYSTEM SETUP To return to the prerecorded announcement 1 2 3 4 Press and release U until you hear "Set outgoing message. " Press and release Y. The system plays the current announcement. Press and release D while the announcement is playing. The system prompts "Outgoing message has been erased. " Press and release U to set up another feature -- OR -- Press and release Y to exit. Ring Select and Toll Saver Use Ring Select to select how many times the phone will ring before the system answers a call. Set for 2, 4 or 6 rings, or set to Toll Saver. When you set the system to Toll Saver, the system answers after 4 rings when you have no new messages, and after 2 rings when you have new messages. 1 Press and release U until you hear "Set number of rings. " 2 Press and release S until you hear your desired setting (2, 4, 6 or Toll Saver). 3 Press and release C to confirm your selection. The system announces your ring selection. 4 Press and release U to set up another feature -- OR -- Press and release Y to exit. Audible Message Alert If you want the base to beep once every 10 seconds to notify you that new messages have been received, set the Message Alert to ON. (The Message Window displays ON for on, and OF for off. ) 1 Press and release U until you hear "Set audible message alert. " 2 Press and release S. The system announces the current setting. 3 Press and release S until the system announces your selection (on or off). 4 Press and release C to confirm your selection. [. . . ] If the system's memory becomes full during a message, the system stops recording and disconnects the call. If you have difficulty hearing messages: Check the volume setting on the base. If the system does not answer after the correct number of rings: · · · · Make sure the ON/OFF light is on. If Toll Saver is on, the number of rings changes to two when you have new messages waiting. In some cases, the system may be affected by the ringing system used by the local telephone company. If the memory is full or the system is off, the system answers after 10 rings. If CL appears in the Message Window: You need to reset the clock. 25 9050_book. 1AT&T 25 8/12/98, 4:15 PM IN CASE OF DIFFICULTY If the system does not respond to remote commands from a touch tone phone: · Make sure you are calling from a touch tone phone. [. . . ]