User manual AT&T AS45

[. . . ] REVISED 1/18/99 1 User's Manual for Tapeless Digital Answering System with Time/Day AS45 Fold open this manual for information about this product's installation and operation. Please read Part 1 ­ Important Product Information, included in this package. Part 2 © 1999 Lucent Technologies Consumer Products L. P. 848317715 Issue 1AT&T INSTALLATION TEL LINE TEL SET Strain Relief Tab Standard Electrical Outlet Modular Telephone Jack Telephone Set Cord Power Cord Telephone Line Cord 1 Connect the telephone line cord. Plug one end of the telephone line cord into the jack labeled TEL LINE on the back of the system. [. . . ] The system announces the number of messages and beeps twice. 3 Wait four seconds for the system to play back all messages -- OR -- Enter a remote command from inside this card. AS45 WC_1ATT 1 1 Tapeless Digital Answering System AS45 Remote Commands To connect with your answering system: 1 Dial your telephone number from a touch tone phone. 2 When the system answers, enter your Remote Access Code. The system announces the number of messages and beeps twice. 3 Wait four seconds for the system to play back all messages -- OR -- Enter a remote command from inside this card. 1/18/99, 2:21 PM fold fold © 1999 Lucent Technologies Consumer Products L. P. 848317749 Issue 1AT&T © 1999 Lucent Technologies Consumer Products L. P. 848317749 Issue 1AT&T ONE KEY REMOTE COMMANDS Play All Play New Delete ONE KEY REMOTE COMMANDS Play All Play New Delete Repeat Stop/Exit Skip Repeat Stop/Exit Skip Annc. Annc. System On Record Memo System On Record Memo TWO KEY REMOTE COMMANDS Turn system off Delete all messages Record announcement Room monitor 00 33 7 *, speak after beep, press 5 to stop 9 8, press 8 to speak with someone in the room; press 5 to exit *9 2 TWO KEY REMOTE COMMANDS Turn system off Delete all messages Record announcement Room monitor 00 33 7 *, speak after beep, press 5 to stop 9 8, press 8 to speak with someone in the room; press 5 to exit *9 Review announcement 7 1 Review announcement 7 1 End remote access call AS45 WC_1ATT End remote access call 1/18/99, 2:21 PM REVISED 1/18/99 INSTALLATION TEL LINE TEL SET OPERATION Displays number of messages and other information OPERATION Answering Calls When the system answers a call, the caller hears the announcement you recorded, followed by a beep. After the beep, the system begins recording your caller's message. A caller can leave a message up to three minutes long. If the message is longer than three minutes, or if the caller is silent for more than seven seconds, or if the system runs out of memory, the system beeps once and hangs up. Callers can skip over your announcement by pressing #. Press P to exit -- OR -- The system will time out after 30 seconds and save any changes already made. Ring Select and Toll Saver Use Ring Select to choose how many times the line will ring before the system answers a call. When you set the system for Toll Saver, it answers after four rings when you have no new messages, and after two rings when you have new messages. 1 Press and hold S for about two seconds. The system announces the current ring selection. 2 Press and release or until the system announces your ring selection. 3 Press and release P to exit -- OR -- Press and release S to change the Remote Access Code (follow Steps 2­5 under "Remote Access Code"). Strain Relief Tab Standard Electrical Outlet Modular Telephone Jack Telephone Set Cord Set and hear time/day Use with other buttons to change/hear settings Turn system on or off Power Cord Telephone Line Cord Adjust volume Delete all or selected messages Record and play outgoing announcement / Skip all or part of a message Microphone Message Window The Message Window displays the number of messages that have been recorded. If there are more than nine messages recorded, the Message Window alternately displays the two digits of the total number of messages recorded. If the Message Window displays F, then the memory is full and you'll need to delete messages before new ones can be recorded. 1 Connect the telephone line cord. Plug one end of the telephone line cord into the jack labeled TEL LINE on the back of the system. Plug the other end into a modular telephone jack. Connect the telephone. 3 1 User's Manual for Tapeless Digital Answering System with Time/Day AS45 Fold open this manual for information about this product's installation and operation. [. . . ] To skip part of a message -- Hold down 6. To stop message playback -- Press and release 5. To save messages, hang up. · · Power Failure Recovery If the system is disconnected from AC power it will not operate. Your announcement and messages are retained in memory during a power failure, but you will need to reset the clock. [. . . ]