User manual ATIKA ATS 250 BROCHURE

[. . . ] Declare under our sole responsibility, that the product Circular Saw Bench ATS 250 Type 250 C to which this declaration relates corresponds to the relevant basic safety and health requirements of the Directive 98/37/EC, and to the requirements for the other relevant Directives: 89/336/EWG, 73/23/EWG. Model designation Motor output P1 Mains voltage Mains frequency Saw blade speed Mains fuse Hard metal saw blade maximum Hard metal saw blade minimum Saw blade thickness Cut width Number of teeth Thickness of Splitting wedge Saw blade location hole Cutting speed (at maximum saw blade ) Cutting height at 90° (for maximum saw blade ) Cutting height at 45° (for maximum saw blade ) Bevel cut adjustment (swivelling range) Table size (without extension) Table height (with stand) * Table length extension * Table width extension * Weight (with stand) * TKS 250 C (ATS 250) 1700 W 230 V~ 50 Hz 4500 min ­1 10 A inert 250 mm 245 mm 1, 8 mm 2, 8 mm 36 2 mm 16 mm 59 m / s approx. Exhaust outlet guard 30 mm Exhaust outlet 30 mm Commercial, small dust collectors or industrial vacuum cleaners are used for vacuuming. You must not start up the machine until you have read these operating instructions, observed all the information given and assembled the machine as described. [. . . ] An exception is youngsters under the age of 16 within the scope of their vocational training under supervision Keep other persons away Do not allow other persons, especially children, to touch the tool or cable. Take up a working position, in which you are always to the side of the saw blade outside of the cutting level Only begin cutting when the saw blade has reached the required speed 12 You work better and safer in the given performance range Only operate the machine with complete and correctly attached safety equipment and do not alter anything on the machine that could impair the safety Do not used cracked saw blades or those that have changed shape Only use well sharpened saw blades, as blunt saw blades not only increase the risk of throw-back errors, but also load the motor Do not use saw blades made of high-alloy high-speed tool steel (HSS), because this steel is hard and brittle, only tools in accordance with EN 847 ­ 1 may be used. The use of other tools and other accessories can signify a risk of injury for you. It is set in the works so that its distance from the toothed ring above the table must Not be more than 5 mm Do not use the saw for unsuitable purposes (see 'Normal intended use'). When longitudinally cutting narrow workpieces (distance between the saw blade and the parallel rip fence less than 120 mm), use the pushstick. (see working instructions) To push narrow workpieces against the parallel rip fence, use a pushstick. Pushsticks can be purchased in retail outlets Do not use defective pushsticks The upper saw blade guard must always be used except for blind cuts. It must be adjusted so that the toothed ring is covered except for the part required for machining the workpiece Ensure that cut off pieces are not caught up by the saw blade and projected away Do not remove splinters, chips and waste from the hazardous area of the saw blade by hand It is not permissible to use wobble devices and groove milling tools Cutting logs with the standard feed guides is not permissible. When cutting logs, use a special device, which secures the workpiece on both sides of the saw blade against turning Switch the machine off and remove the mains plug from the socket when - carrying out repair works - carrying out servicing and repair works, removal of faults (this also includes removing clamped splinters) - Transporting the saw - Changing the saw blade - leaving the saw unattended (even during short interruptions) Look after your saw with care - Keep the tools sharp and clean to be able to work better and more safely - Follow the servicing instructions and the information about changing tools - Keep handles dry and free of oils and grease Check the machine for possible damage - Before continuing to use the machine, the protective devices must be inspected to ensure that they work perfectly and with their intended function - Check whether the movable parts function perfectly and do not stick or whether the parts are damaged, All parts must be correctly installed and fulfil all conditions to ensure perfect operation of the saw - Damaged guards and parts must be properly repaired or exchanged by a recognized, specialist workshop; insofar as nothing else is stated in the instructions for use. Do not allow any tool key to be plugged in!Store the unused machine in a dry locked place away from the reach of children Place the saw in a place that fulfils the following conditions: secured against slipping free of vibrations even free of tripping hazards adequate light · Before each use, check - Connection cables for defects (cracks, cuts, etc. ) Do not use any defective cables - that the guard is in a proper condition - the splitting wedge setting (see splitting wedge setting) - that the saw blade is in a perfect condition - whether the pushstick is to hand · Do not use any cracked saw blades or those that have changed their shape · Do not use any saw blades made of HSS steel · When sawing, place yourself to the side of the danger area (saw blade) · Lower the guard onto the bench top - when working on the workpiece - when interrupting the work or leaving the saw Design of the connection cable according to IEC 60 245 (H 07 RN-F) with a core cross-profile section of at least 1. Avoid touching earthed parts with your body. Do not use the cable for purposes for which it is not meant. Protect the cable against heat, oil and sharp edges. Do not use the cable to pull the plug from the socket. regularly check the saw cable and if damaged , have it renewed by a recognised skilled electrician. Regularly check the extension cables and replace them if they are damaged Do not use any defective connection cables When working outdoors, only use extension cables especially approved and appropriately labelled for outdoor use Do not set up any provisional electrical connections Never bypass protective devices or deactivate them. The electrical connection or repairs to electrical parts of the machine must be carried out by a certified electrician or one of our customer service points. Other saw blades are available for other uses on request. The transverse stop supplied can be used as a transverse or mitre stop. Make sure that the fences are correctly adjusted. [. . . ] Without suction Remove the mains plug from the socket Store unused equipment in a dry, locked place out of the reach of children. To extend the service life of the saw and guarantee smooth operation, before storing for a longer period - thoroughly clean the saw - treat all movable parts with an environmentally friendly oil We grant a guarantee of two years, commencing with the day of delivery from the dealer's store, for material and manufacturing faults. Warranty claims, even during the warranty period, will not be accepted for damages due to incorrect handling or inadequate packaging during return of the devices or to a non-observance of the operating instructions. Faulty parts must be sent to our works, postage or freight free. [. . . ]